WEG CFW300 V1.3X, Руководство по программированию

Страница: 75 / 157

VVW Vector Control
CFW300 | 10-3
10
10.1 VVW VECTOR CONTROL PARAMETERIZATION
The V VW control mode is selected by parameter P202, control mode selection, as described in Chapter 8
AVAILABLE MOTOR CONTROL TYPES on page 8-1 .
Opposite to the V/f scalar control, the V VW control requires a series of data from the motor nameplate and a
self-tuning for its proper operation. Besides, it is recommended that the driven motor match the inverter, that is,
the motor and inverter power be as close as possible.
Below are described the parameters to configure the V VW vector control setting. This data is easily obtained on
WEG standard motor nameplates, however in older motors or motors made by other manufacturers, the data
may not be readily available. In those cases, it is recommended first contact the motor manufacturer, measure or
calculate the desired parameter. As a last resort, the user always can make a relationship with
Table 10.1 on page
10-3 and use the equivalent or approximate WEG standard motor parameter.
NOTE!
The correct setting of the parameters directly contributes to the V VW control performance.
Table 10.1: Characteristics of IV pole WEG standard motors
Power [P404]
Frame
size
Voltage
[P400]
(V)
Current
[P401]
(A)
Frequency
[P403]
(Hz)
Speed
[P402]
(rpm)
Efficiency
[P399]
(%)
Power
Factor
Stator
Resistance
[P409]
(Ω)
(HP) (kW)
0.16 0.12 63
220
0.85
60
1720 56.0 0.66 21.77
0.25 0.18 63 1.12 1720 64.0 0.66 14.87
0.33 0.25 63 1.42 1720 67.0 0.69 10.63
0.50 0.37 71 2.07 1720 68.0 0.69 7.37
0.75 0.55 71 2.90 1720 71.0 0.70 3.97
1.00 0.75 80 3.08 1730 78.0 0.82 4.13
1.50 1.10 80 4.78 1700 72.7 0.83 2.78
2.00 1.50 90S 6.47 1720 80.0 0.76 1.55
3.00 2.20 90L 8.57 1710 79.3 0.85 0.99
4.00 3.00 100L 11.6 1730 82.7 0.82 0.65
5.00 3.70 100L 13.8 1730 84.6 0.83 0.49
0.16 0.12 63
230
0.73
50
1375 57.0 0.72 30.62
0.25 0.18 63 1.05 1360 58.0 0.74 20.31
0.33 0.25 71 1.4 1310 59.0 0.76 14.32
0.50 0.37 71 1.97 1320 62.0 0.76 7.27
0.75 0.55 80 2.48 1410 68.0 0.82 5.78
1.00 0.75 80 3.23 1395 72.0 0.81 4.28
1.50 1.10 90S 4.54 1420 77.0 0.79 2.58
2.00 1.50 90L 5.81 1410 79.0 0.82 1.69
3.00 2.20 100L 8.26 1410 81.5 0.82 0.98
4.00 3.00 100L 11.3 1400 82.6 0.81 0.58
5.00 3.70 112M 14.2 1440 85.0 0.83 0.43
P178 - Rated Flux
Adjustable
Range:
50.0 to 150.0 % Factory
Setting:
100.0 %
Properties: V VW
Description:
It defines the desired flux in the motor air gap in percentage (%) of the rated flux. In general, it is not necessary
to modify the value of P178 of the standard value of 100 %. However, some specific situations may use values
slightly above to increase the torque, or below to reduce the energy consumption.