manualshive.com logo in svg

Weco Pioneer Pulse 321MKS, Инструкция по эксплуатации, Страница: 24 / 48

Поделиться
Скачать
Weco Pioneer Pulse 321MKS Скачать руководство пользователя страница 24

Cod

. 006.0001.1600

11/07/2022 V.2.12

Pioneer 321 MKS

24

ENGLISH

5.2  PARAMETERS ACTIVATION

The welding parameters are available in accordance with the selected welding mode and procedure. 

The table shows the settings required to enable each parameter.

KEY

1: Not enabled with manual program P0.

2: Always available.

 - Parameters activation

PROCEDURE 

MENU

PARAMETER 

1st

WORKING VOLTAGE

2

2

1

1st

INDUCTANCE

2

2

1

1st

WIRE FEED RATE

2

2

1

1st

WELDING CURRENT

1

1

1

1st

THICKNESS

1

1

1

1st

PROGRAMS

2

2

1

2°

HOT-START

1

2nd

CRATER FILLER

1

2nd

3 LEVELS SLOPE

1

2nd

SOFT START

2

2

1

2°

MOTOR SLOPE

2

2

1

2nd

BURN BACK

2

2

1

GAS

POST GAS TIME

2

2

1

GAS

PRE-GAS TIME

2

2

1

5.3  WELDING PARAMETERS

WELDING CURRENT

Output current value during welding.

HOT-START

This function is useful when using aluminium alloy welding wire.

Consequences of a higher value:

 -

Greater heat output.

 - Greater penetration.

Consequences of a lower value:

 -

“Cold” weld bead.

MOTOR SLOPE

Time required to switch from SOFT START speed to welding speed.

ARC CORRECTION IN VOLTS

This parameter corrects the synergic voltage value relative to the synergic point of the MIG/MAG pro

-

cesses.

The default value for horizontal and frontal welding is 0.0 V.

Содержание Pioneer Pulse 321MKS

















































Отзывы:

Нет отзывов