manualshive.com logo in svg

Weco Pioneer Pulse 321MKS, Инструкция по эксплуатации, Страница: 20 / 48

Поделиться
Скачать
Weco Pioneer Pulse 321MKS Скачать руководство пользователя страница 20

Cod

. 006.0001.1600

11/07/2022 V.2.12

Pioneer 321 MKS

20

ENGLISH

3.5  LOCKING PROCEDURE

The procedure inhibits unit adjustments, allowing the user to modify only certain settings depending on 

the selected lock status.

The procedure is used to prevent accidental alteration of the unit settings and welding settings by the 

operator.

Enabling

If no locking status is selected (LOC = oFF) and if you wish to set up a limitation on use of the power 

source, display the LOC function in the SETUP menu.

Open the Setup menu.

 

 

The acronym relative to the setting to be edited appears on the following displays: D1

 

 

The value relative to the selected setting appears on the following displays: D2

E1 

 

Use the encoder to select the following setting: LoC

E2 

 

Use the encoder to select the required lock status.

 

i

 

Depending on the selected Lock, certain functions will remain enabled.

E1 

 

Use the encoder to select the following setting: ESC

S4 

 

Press any button to save the setting and quit the menu.

 - Functions not disabled by Locks

LOCK 

STATUS 

USER INTERFACE

RC03

RC04

RC05

RC06

OFF

All adjustments enabled.

Key K1 disabled.

All adjustments 

enabled.

All adjustments 

enabled.

All adjustments 

enabled.

All adjustments 

enabled.

1

Selection of torch trigger procedure 

(button S5)

Display of main welding parameters 

(button S4)

Arc correction (encoder E2)

Wire insertion (button S1)

Gas test (button S2)

Arc correction 

(Potentiometer 

Pot2)

Arc correction 

(UP/DOWN 

lever 2)

2

Selection of torch trigger procedure 

(button S5)

Display of main welding parameters 

(button S4)

Arc correction (encoder E2)

Synergy (encoder E1)

Wire insertion (button S1)

Gas test (button S2)

All adjustments 

enabled.

All adjustments 

enabled.

All adjustments 

enabled.

All adjustments 

enabled.

3

Selection of torch trigger procedure 

(button S5)

Display of main welding parameters 

(button S4)

JOB selection (encoder E2)

Wire insertion (button S1)

Gas test (button S2)

Scroll JOBS 

(UP/DOWN 

lever 1)

Scroll JOBS 

(UP/DOWN 

lever 1)

Содержание Pioneer Pulse 321MKS

















































Отзывы:

Нет отзывов