background image

27

WWW.WEBER.COM

®

27

VENTILATION

WARNING: Air holes must be provided in the structure at the 

top and bottom to provide ventilation in the event of a gas leak.

Air holes can be located in a low visibility area and should be protected by screening 
material to prevent rodents and insects from entering the structure. Air holes will also help 
dry moisture.
Summit

®

 Built-In cabinet vents are available from your dealer or call Customer Service at 

1-800-446-1071. 

Note: These drawings are only a reference.
• 

Cross ventilation must be incorporated in the supporting structure. We recommend 
a minimum of 100 square inches (254 square cm )of venting per side.

• 

Vents should be on two sides of the structure. 

• 

The above drawings are for reference only.

• 

Location of the vents should be from the center, outward.

• 

Locate the vents at both the bottom of the structure and at the top of the structure.

• 

The bottom vents should be as close to ground level as possible. Make sure the 
vent area is not blocked by interior supports of the structure.

• 

We recommend vents with screens.

• 

Access doors to the structure are not considered vents.

• 

Clean the vents periodically.

 

DANGER: Failure to follow recommended minimum venting 

instructions can cause gas to collect in the structure in the 
event of a gas leak. This may result in a fi re or an explosion 
which can cause serious bodily injury or death, and damage to 
property.

 

ATTENTION: This product has been safety tested and 

is only certifi ed for use in a specifi c country. Refer to 
country designation located on outer carton. 

These parts may be gas carrying or gas burning components. Please 
contact Weber-Stephen Products Co., Customer Service Department 
for genuine Weber-Stephen Products Co. replacement part(s) 
information.

 

WARNING: Do not attempt to make any repair to 

gas carrying or gas burning components without 
contacting Weber-Stephen Products Co., Customer 
Service Department. Your actions, if you fail to follow 
this product Warning, may cause a fi re or an explosion 
resulting in serious personal injury or death and 
damage to property.

GAS SUPPLY

Содержание Summit S-440





























Отзывы: