manualshive.com logo in svg

Weber PLATINUM 3200 Series, Руководство пользователя

Поделиться
Скачать
Weber PLATINUM 3200 Series Скачать руководство пользователя страница 19

19

Step 19

Install tool holders, control panel and burner
control knobs

You will need: three tool holders, control panel, two Phillips
screws/washers, a Phillips screwdriver, and three burner
control knobs.

Hook the tool holders over the frame rail. Figure 25.

Set the control panel in place over both frame braces. (Hold
the Crossover Ignition button up while setting the control
panel in place.) Line up the holes in the control panel with
the holes in the inserts in the frame brace. Insert screws
and tighten with a Phillips screwdriver until snug. Do not
overtighten. Figure 25 (a). 

Push on the burner control knobs. Figure 25 (b).

Figure 25

Tool holders

(a)

(b)

Step 20

Secure side burner

Pull the right hand swing table up. Stand to the right side
of the barbecue. Slightly pull back both side burner locks.
Slide the side burner toward the control panel. The locks
will snap into the slots in the front and back of the side
burner. Figure 26.

CAUTION: Make sure both locks have snapped 

into place.

Figure 26

View from top

View from side

Control panel

Phillips screws/

washers

Insert in

frame brace

Crossover

Ignition Button

Содержание PLATINUM 3200 Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды