Weber GENESIS 3000 LX Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 36

background image

Step 4

Continue frame assembly

You will need: frame assembly, wheel frame assembly,
front panel, caster frame, four 1/4-20 x 1/2 inch bolts, four
nylon washers and a 7/16 inch wrench.

Place the caster frame onto the tabs of the left frame with
the dimple to the inside. Figure 3. Place the wheel frame
onto the tabs of the right frame with the dimple to the
inside. Figure 3.

The leg tabs must be on the inside of the frames.

Add front panel with the large hole down and to your right.
Add the washers to the bolts, insert in the holes as shown
and tighten with the wrench. Figure 3. Only start the bolt at
the wheel frame/right joint opposite the front panel. Figure 3.

Dimples to
the inside

Only start
this bolt

Figure 3

Fully tighten
this bolt

11

Step 5

Complete frame assembly

You will need: partial frame assembly, two frame
connectors, four 1/4-20 x 2 inch bolts, four nylon washers
and a 7/16 inch wrench.

Hold one frame connector between the caster and wheel
frame. Add nylon washers to the bolts. Put the bolts
through the frame and screw into frame connector. Tighten.

Repeat procedure with the other frame connector. Figure 4.

Figure 4

«
...
9
10
11
12
13
...
»

Содержание GENESIS 3000 LX





































Отзывы:

Нет отзывов

Похожие инструкции для GENESIS 3000 LX

Бренд: Backyard Pro Страницы: 11

Бренд: Felisatti Страницы: 36

Бренд: Magikitch'n Страницы: 4

Select CBC1684W-U

Бренд: Uniflame Страницы: 16

Бренд: Uniflame Страницы: 14

Бренд: Ryobi Страницы: 14

Бренд: Felisatti Страницы: 31

Бренд: Barbecook Страницы: 128

Бренд: Powerplus Страницы: 11

Бренд: Ryobi Страницы: 87

Fancy Flames FF445

Бренд: Esschert Design Страницы: 8

Бренд: inventum Страницы: 32

Spirit Premium 320

Бренд: Weber Страницы: 12

Monterey II A10-1225-2

Бренд: Magma Страницы: 8

Summit Gold D 42080

Бренд: Weber Страницы: 50

Бренд: XTline Страницы: 81

Бренд: XTline Страницы: 81

Бренд: Hilti Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды