Weber mt SRV 600 i Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

background image

16

SRV 600i

1

1

2

1

1

1

2

Change the built-in fuel filter

Pull the fuel line (1) off the fuel cock (2).

Unscrew the fuel cock, including fuel filter (1) out of the

fuel tank.

Clean the fuel filter.

Replace fuel filter if damaged.

Clean/change air filter cartridge

Remove the air filter cover (1).

Remove the air filter insert (1) from the air filter enclosure /

air filter cover.

Clean air filter insert as specified by the engine manufacturer

if there is damage or if it is extremely dirty.

Changing the engine oil

Remove the oil dip stick (1).

Open the drain plug (2) of the engine and drain oil.

Danger of scalding due to hot oil.

Check the oil fill level with the oil dip stick again.

Maintenance work

Screw in the oil drain plug (2) with new seal and top off

with oil as specified.

Only drain engine oil when at operating temperature.

When working in the area of the engine compartment

there is a danger of being burnt!

For work at the fuel system, have a suitable fire-

extinguishing agent at the ready.

Fire, naked light, and smoking is forbidden!

UPPER LEVEL

LOWER LEVEL

«
...
14
15
16
17
18
...
»

Содержание SRV 600 i

























Отзывы:

Нет отзывов

Похожие инструкции для SRV 600 i

Бренд: swepac Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды