background image

20

8. Maintenance

General information

The section below contains instructions that need to be 

observed for regular maintenance. Read these instructions 

carefully and follow them in order to prevent downtimes of the 

machine caused by excessive wear or damage to the machine.

Also read the safety instructions relevant to machine 

maintenance before you begin with the maintenance work. 

They help minimize the risk to maintenance personnel. 

Maintenance personnel

Maintenance and repairs require specific qualifications. These 

operations may only be carried out by trained professionals.

Maintenance personnel must be instructed on how to operate 

the machine by the owner or by the owner’s assigned 

personnel. 

Maintenance personnel are required to wear the personal 

protective equipment during work (see section “Safety“). 

Safety

There is an increased risk of injury during maintenance 

and repairs, e.g. crushing at moving parts.

Following the conclusion of all maintenance and repairs, 

all protective fixtures must be refitted and placed back into 

operation.

Discharged operating fluids have a negative impact on the 

environment. They must be collected and stored in suitable 

containers. Disposal in accordance with environmental 

protection regulations.

All maintenance work may only be carried out when the engine 

is cold. Safeguard the engine against unauthorized start 

attempts.

Before working on the electrical system, disconnect the starter 

battery and cover the battery terminals with insulating material. 

It is also recommended to disconnect the battery as a means 

to safeguard the machine against unauthorized start attempts 

during maintenance work.

Before starting the machine after maintenance operations, 

make sure that all loose parts (screws, tool, etc.) have been 

removed from the machine. They may be drawn in or flung off 

by moving parts.

Keep the entire machine clean. The stickers must always 

be clearly legible. Damaged stickers must be replaced.

Содержание 0116261





























Отзывы: