Weber mt 0116261 страница 26 Скачать руководство пользователя

Страница: 26 / 28

8.2.10. Use a permanent

charger

Open the protective cover (1) of the charging socket.

Connect the permanent charger to the charging socket.

Connect the permanent charger to the appropriate mains

supply.

Comply with the manufacturer’s operating manual

when using the permanent charger! The operating

manual is included with every permanent charger.

8.2.9. Change the oil in

the exciter

Start the engine and allow the engine to warm up for

a few minutes.

Switch off the engine.

Tilt the machine slightly.

Place a suitable collection vessel under the machine.

Loosen the oil drain plug.

Allow the oil to drain.

Tilt the machine in the other direction.

Fill fresh oil into the exciter in accordance with the

specification.

Close the oil drain plug.

Содержание 0116261





























Результаты поиска

Содержание 0116261

Отзывы:

Похожие инструкции для 0116261

Бренды по названию

Популярные бренды

Weber mt 0116261, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 0116261

Отзывы:

Похожие инструкции для 0116261

Бренды по названию

Популярные бренды