background image

Installation and electrical connection | 8

5111232A OI-II Webasto Next

9 / 23

8

Installation and electrical
connection

DANGER

Observe the safety information provided here
chapter 2, "Safety" on page 4.

To access further documents use one of the following options:

Webasto Service App

To download this app:

u

scan the QR code below or

u

go to: 

https://apps.apple.com/

 (Apple App Store) or

https://play.google.com/

 (Google Play Store) as appropri-

ate.

To use the Webasto Service App and access online Webasto
technical documentation, please scan the QR code or the bar-
code on your Webasto product box.
Our operating instructions are also available on our website at

http://www.webasto-charging.com/documentation

. All lan-

guages can be found in the download portal on our website.

NOTE

The Webasto Next safety concept is based on a power
supply system that is earthed at all times, which must
always be ensured by an electrician during installation.

Webasto ChargeConnect App

To download this app:

u

scan the QR code below or

u

go to: 

https://apps.apple.com/

 (Apple App Store) or

https://play.google.com/

 (Google Play Store) as appropri-

ate.

Webasto Charger Setup App

To download this app:

u

scan the QR code below or

u

go to: 

https://apps.apple.com/

 (Apple App Store) or

https://play.google.com/

 (Google Play Store) as appropri-

ate.

8.1

Requirements installation space

The following points must be taken into account when selecting
the installation location for the Webasto Next:

l

The lower edge of the enclosed mounting template must
be at a minimum distance of 90 cm above the ground dur-
ing installation. See Fig. 13.

l

If several charging stations are installed next to each other,
a spacing of at least 200 mm must be maintained between
each station.

l

The mounting surface must be solid and strong.

l

The mounting surface must be completely flat (max. 1 mm
difference between the individual mounting points).

l

The mounting surface must not contain any flammable sub-
stances.

l

A cable run from the charging station to the vehicle as
short as possible.

l

No risk of driving over the charging cable.

l

Possible electrical connections from infrastructure.

l

Pavements and escape routes must not be obstructed.

l

We recommend an installation location that is protected
against direct sunlight for optimum and fault-free opera-
tion.

l

The usual parked position of the vehicle, taking account of
the position of the charging plug on the vehicle.

l

Consideration of local building and fire protection regula-
tions.

NOTE

The mounting distance between the bottom edge of
the charging station and the floor must be at least 0.9
m.

Содержание Next
























Отзывы: