Weaver Baldwin 2-8-0 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 10

Weaver Baldwin 2-8-0 Скачать руководство пользователя страница 7

Page 7

Step 6: Now press AUX1 and 8. (This sets the smoke unit output on the receiver.)
Step 7: Set the PROGRAM / RUN switch to RUN.

Your engine remembers its ID# forever, change it any time with these steps.

EOB Speed Control Operating Instructions

Your Baldwin 2-8-0 is equipped with Train America Studios EOB® Speed

Control to provide the best in operating realism. EOB is a constant speed control
system designed to maintain a constant speed regardless of track conditions, load or
grade. EOB offers 3 different modes of operation when using the Trainmaster®
Command operating system. These modes are 32 speed steps, cruise on
(programmed in this mode from the factory), 128 speed steps, cruise on and 32 speed
steps, cruise off. In addition to these different speed steps you can also change the
chuff rate of your locomotive on the fly! EOB uses its own set of Cab-1 Remote® keys
to change these settings. Please see the instructions below for detailed information.

32 Speed step mode, Cruise On

This mode is used to perform lashups with Lionel® Odyssey® equipped

locomotives. It provides 32 speed steps from a dead stop to full speed. All commands
from the Cab-1® work the same as any other command equipped locomotive. To
access the 32 speed step feature you can use the following key sequence on the Cab-
1® remote.

ENG + ID DIR + AUX1 + AUX1 + AUX1 + 1

The whistle will blow after the 3rd AUX1 and again after 1. These whistles are

to verify the locomotive took the commands you sent. Your locomotive is programmed
in the 32 speed step mode, cruise on from the factory.

128 Speed step mode, Cruise On

This mode is used to provide finer control of your locomotive's speed and for

lashups with other EOB equipped locomotives. It provides 128 speed steps from a
dead stop to full speed. The keys on the Cab-1® remote will work slightly different from
what you may be accustomed to. The Boost key increases the speed steps one at a
time. The Brake key decreases the speed steps one at a time (holding the Brake key
down in the 128 mode will NOT yield the squealing brake sounds). Turning the red
thumbwheel on the Cab-1® clockwise will increase the speed steps two at a time,
counter-clockwise will decrease the steps four at a time. These new keys may take
some time to get used to, but will prove to be very effect in operating your locomotive.
To access the 128 speed step feature you can use the following sequence on the Cab-
1® remote.

«
...
5
6
7
8
9
...
»

Содержание Baldwin 2-8-0











Отзывы:

Нет отзывов