manualshive.com logo in svg

Weatherford SLS Baseline 8900, Руководство по установке, настройке и калибровке

Поделиться
Скачать
Weatherford SLS Baseline 8900 Скачать руководство пользователя страница 6

 

SLS Baseline 8900 Setup and Calibration Manual                  5-1-GL-GL-SUL-00028 

Page 5 

 

SAFETY NOTICES 

 

This is analytical laboratory equipment; please use the following laboratory practices: 

 

Do not allow gas lines to become kinked or punctured.  

 

Place lines away from foot traffic and extreme heat or cold. 

 

Store gases in clearly-labeled cabinets. 

 

Run all vents and exhaust lines external to the logging unit or work area. 

NOTE 

The CP-4900 is a laboratory grade instrument.  As such it should be handled 
with care to avoid excessive vibration and mechanical shock or impact. 

NOTE

 

All stainless steel tubing used with the chromatograph should be 
chromatograph grade. 

NOTE 

Do not touch the knobs on the back of the Baseline 8900. If they are adjusted, 
the flow calibration will be incorrect and the instrument will have to be sent 
back to Baseline for recalibration 

NOTE 

After powering the instrument down, wait a minimum of 30 seconds to power 
the instrument up again. Failure to do so may cause damage to the 
instrument 

NOTE 

Do not power on the Baseline 8900 without the proper support gases 
connected. Doing so may cause damage to the instrument. 

Содержание SLS Baseline 8900


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды