WCS WPL VSF04 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 26

WCS WPL VSF04 Скачать руководство пользователя страница 21

Operation & Maintenance Manual

20 |

P a g e

APPENDIX 1

KIOSKS AND BASE SLABS

WPL supplies a wide variety of blower types depending on the size of plant and site requirements. It is
not possible therefore to demonstrate in a general manual the layout for the ducting exit for each kiosk.
However, WPL will provide drawings on request

showing the layout of the client’s bespoke kiosk.

For each kiosk type there is however one standard concrete slab size and listed below are kiosk
descriptions and slab sizes. In each case the slab should be cast deep enough to take the weight of the
blower(s) designated. Please refer to WPL before laying the concrete.

Medium Kiosk

WPL’s medium kiosk has a gull

-wing type opening, with the front hinging upwards to give easy access.

The concrete slab should be 1200mm x 950mm.

Large Kiosk

The large kiosk has a standard front opening door. The concrete slab should measure 1400mm x

1600mm.

Extra Large Kiosk

This kiosk has a gas-strut supported opening lid and door for easy access. The concrete slab for this item
should be 1400mm x 2200mm.

Note:

➢

Ensure that there is unobstructed air flow from all the vents otherwise overheating will
occur.

➢

Ensure the kiosk is installed above any areas likely to flood.

«
...
19
20
21
22
23
...
»

Содержание WPL VSF04



























Отзывы:

Нет отзывов