background image

DC ROUTINE SUMP MAINTENANCE

  Once a month, check the battery condition. To check battery condition follow steps Listed below:

1.   Unplug the transformer.

NOTE: 

An inexpensive hydrometer can be purchased at an automotive parts dealer. 

2.   Inspect the terminals and clamps for corrosion and  
tightness. Clean and tighten as required. 

3.   Unplug the main pump and fill sump with water until backup pump turns on. Repeat process two times to make sure pump is 
operating normally. 

4.   If pump operates normally, plug transformer into wall outlet, turn on main pump. If pump fails to operate normally, see Trouble-
shooting guide and correct problem. 

 

DC TROUBLESHOOTING CHART

Symptoms

Possible Cause(s)

Suggested Remedies

Pump will not  
start or run 
 
 
 
 
 
 

1.  Connections not secure
2.  Low or defective battery
3.  Float switch stuck

4.  Defective or blown fuse

5.  Battery voltage below threshold, 

motor locked out

1.  Check all connections
2.  Check battery and replace as needed
3.  Make sure nothing is interfering with operation of switch
4.  Pull the transformer from the wall outlet and remove. Check the 

20 Amp Automotive Sytle fuse located under the battery box lid 
protruding from printed circuit board cover

5.  Wait for battery to recharge or replace with fresh battery

Motor hums but 
won’t run

1.  Defective battery
2.  Locked pump rotor

1.  Check battery and replace if low or defective
2.  Check pump inlet for debris

Pump runs but 
pumps very little 
or no water

1.  Check valve missing or improperly 

installed

2.  Obstruction in discharge pipe
3.  Discharge length an/or height 

exceeds capacity of pump

4.  Low or defective battery

1.  Check to make sure check valve installed in discharge and line is 

functioning properly

2.  Check for obstruction and clear if necessary
3.  If discharge is too high, a seperate line may be required with a lower 

discharge height

4.  Check battery and replace as needed

Pump cycles too 
frequently

1.  Check valve problem

1.  Check to make sure check valve installed in discharge and line is 

functioning properly

10

www.waynepumps.com

Operating Instructions and Parts Manual

Содержание WSS30Vn













Отзывы: