manualshive.com logo in svg

Wayne 3/VISTA series, Руководство по обслуживанию

Поделиться
Скачать
Wayne 3/VISTA series Скачать руководство пользователя страница 35

31

June 2001

Part No. 920525 Rev A

4.  MECHANICAL PARTS

4.1.

 NOZZLE BOOT (PROXIMITY “REED” SWITCH STYLE BOOT)

The nozzle boot assembly, used on the dispenser models covered in this manual, uses a 
proximity “Reed” switch and magnet for ON/OFF dispenser activation. The nozzle boot 
can be assembled in either the Lift-to-Start or the Push-to-Start configuration.

4.1.1.

Lift-to-Start Version

The nozzle boot switch assembly (see section 10) consists of a proximity reed 
switch attached to the rear of the nozzle boot casting. A magnet is contained in 
the Lift-to-Start lever and when the lever is lifted to the ON position the magnet 
is brought into alignment with the proximity switch, turning the switch ON. 
There is no adjustment for the switch.

Check the operation of the nozzle switch as follows:

1. Authorize the dispenser and remove the nozzle from the nozzle boot. Lift 

the nozzle hook lever fully upward to make sure the switch turns ON. An 
ON switch will be indicated by the unit price displays of the unselected 
products going OFF or displaying dashes. 

2. Lower the Lift-to-Start lever to the down position and check that the switch 

turns OFF. An OFF switch is indicated by the unit price displays of the unse-
lected products coming back ON.

4.1.2.

Push-to-Start Version

The nozzle boot switch assembly (see section 10)) consists of a proximity reed 
switch attached to the side of the nozzle boot casting and a magnetic actuator 
shaft inserted into a spring-loaded flipper within the nozzle boot. When the 
nozzle is removed, the flipper rotates and aligns the magnetic shaft with the 
proximity switch, turning the switch ON. There is no adjustment for the switch.

Check the operation of the nozzle switch as follows:

1. Authorize the dispenser and remove the nozzle from the nozzle boot to 

make sure the switch turns ON. An ON switch will be indicated by the 
lighted Push-to-Start buttons and the unit price displays blinking.

2. Insert nozzle slowly into the nozzle boot and check that the switch turns 

OFF. An OFF switch is indicated by the lighted Push-to-Start buttons 
turning OFF and the unit price displays stop blinking.

Содержание 3/VISTA series



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды