Wayne-Dalton TorqueMaster Plus 9800 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 38

background image

Tools Needed:

34

Please Do Not return This Product To The Store.

Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local

yellow pages business listings or go to the Find a Dealer section

online at www.Wayne-Dalton.com

Trolley operator

align hole in the appropriate arm with
holes in operator bracket tabs. Insert
5/16” x 1-1/4” clevis pin, making sure
hole in clevis pin is outside of second
tab of operator bracket. Insert hairpin
cotter into clevis pin hole and spread
hairpin cotter to ensure it will secure
assembly. Operator must be tested at
time of installation and monthly there
after to ensure that door reverses on
contact with 2” x 4” board laid flat under
the door. Failure to pass this test requires
immediate adjustments or repairs.

FaIluRE TO MakE aDjusTMENTs
OR REPaIRs, IF NECEssaRy, CaN
REsulT IN sEVERE OR FaTal
INjuRy.

If your operator is equipped with a
photoelectric eye system, then this must
be tested at the same time to ensure
that door does not close and a closing
door opens, if photoelectric eye system
is obstructed. Failure to pass this test
requires immediate adjustments or
repairs.

FaIluRE TO MakE aDjusTMENTs
OR REPaIRs, IF NECEssaRy, CaN
REsulT IN sEVERE OR FaTal
INjuRy.

1. Install operator rail 1/2” to 1”

(13 mm - 38 mm) above high arc

of top section of the door.

2. Mount operator to ceiling so that

1” to 1-1/2” (25 - 38 mm)

clearance is maintained between

trolley rail and top section when

door is fully open (trolley rail will

slope down towards rear).

3. attach door arm to operator

bracket installed in step 9.

4. attach operator rail to suitable

mounting surface, 2” x 6” lumber

minimum.

5. attach operator to ceiling using

perforated angle.

IMPorTANT!

PERFORaTED aNGlE MusT

BE sECuREly aTTaCHED TO sOuND
FRaMING MEMBER(s).

HEaDER

OPERaTOR

FRaMING

MEMBERs

PERFORaTED aNGlE

OPERaTOR

RaIl

PERFORaTED

aNGlE

OPERaTOR

RaIl

WArNINg

suITaBlE

MOuNTING

suRFaCE (2 x 6)

luMBER MIN.

DOOR aRM TO OPERaTOR

BRaCkET

WArNINg

None

HaIRPIN
COTTER

OPERaTOR

BRaCkET

DOOR

aRM

5/16” x 1-1/4”

ClEVIs PIN

OPERaTOR

BRaCkET

TaBs

DOOR aRM

TOp vieW

HaIRPIN COTTER

(OuTsIDE OF OPERaTOR

BRaCkET TaB)

OPERaTOR

BRaCkET TaBs

«
...
32
33
34
35
36
...
»

Содержание TorqueMaster Plus 9800







































Отзывы:

Нет отзывов

Похожие инструкции для TorqueMaster Plus 9800

Бренд: International Door Closers Страницы: 2

Бренд: CAME Страницы: 96

Бренд: Ribind Страницы: 12

Бренд: Gamatech Страницы: 26

Бренд: SEA Страницы: 20

Бренд: Key Automation Страницы: 60

PowerDrive PD212D

Бренд: Chamberlain Страницы: 40

PowerDrive PD210

Бренд: Chamberlain Страницы: 80

Security+ 1215EM FS2

Бренд: Chamberlain Страницы: 80

Бренд: Roger Technology Страницы: 16

Бренд: tau Страницы: 20

Бренд: CAB Страницы: 15

Estate Swing Heavy Duty Series

Бренд: FAAC Страницы: 33

8K01MB-0576 STYLO KIT

Бренд: CAME Страницы: 12

Бренд: EasyWay Страницы: 43

Бренд: CAME Страницы: 14

Бренд: CAME Страницы: 24

Бренд: vds Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды