Wayne-Dalton EXTENSION 44, Быстрый старт

Страница: 3 / 14

3
A. FLAG ANGLES (AS REQUIRED):
A1. Fully Adjustable (F.A.) Flag Angles
B. JAMB BRACKETS (AS REQUIRED):
B1. Fully Adjustable (F.A.) Jamb Brackets
C. TRACK ROLLERS (AS REQUIRED):
C1. Short Stem Track Rollers / C2. Long Stem Track Rollers
C3. Short Stem Tandem Track Rollers
C4. Long Stem Tandem Track Rollers
D. GRADUATED END HINGES:
D1. Single Graduated End Hinges (S.E.H.), Industry Standard
D2. Double Graduated End Hinges (D.E.H.), Industry Standard
D3. Half Center Hinges (As required)
E. STACKED SECTIONS:
E1. Top Section
E2. Intermediate(s) Section / E3. Bottom Section
F. TOP FIXTURES (AS REQUIRED):
F1. Top Fixture Bases - (L-Shaped)
F2. Top Fixture Slides - (L-Shaped)
F3. “L” Reinforcing Brackets (As Required)
G. STRUT(S) (AS REQUIRED):
G1. Strut (2” U-shaped) / G2. Strut (3” U-shaped)
H. TRACKS (AS REQUIRED):
H1. Left Hand and Right Hand Horizontal Track Assemblies
H2. Left Hand and Right Hand Vertical Tracks
H3. Left Hand and Right Hand Riveted Vertical Track Assemblies
H4. Left Hand and Right Hand Angle Mount Vertical Track Assemblies
J. EXTENSION SPRING ASSEMBLY (AS REQUIRED):
J1. Extension Springs
J2. Spring Restraint Cables
J3. Front Cable Lift Sheaves
J4. Rear Cable Lift Sheaves
J5. 3 Hole Clips (As Required)
J6. Small S-Hooks (As Required)
J7. Sheave Forks (As Required)
J8. 5/16” - 18 x 3-3/4” Eye Bolts (As Required)
J9. Counterbalance Lift Cables
J10. Hook Plates (As Required)
J11. Large S-Hooks (As Required)
K. REAR BACK HANGS:
K1. Left Hand And Right Hand Rear Back Hang Assemblies
K2. Left and Right Hand Rear Center Back Hang Assemblies (As Required)
K3. Left and Right Hand Rear Center Back Hang Assemblies (As Required)
L. BOTTOM CORNER BRACKETS (AS REQUIRED):
L1. Left Hand and Right Hand Bottom Corner Brackets
M. BOTTOM WEATHER SEAL (AS REQUIRED):
M1. Bottom Weather Seal (Door Width), (Nails Not Supplied)
N. TRACK ROLLER CARRIERS (AS REQUIRED):
N1. Track Roller Carriers
C3.
E3.
E1.
E2.
E2.
G1.
K1.
K1.
NOTE: The illustrations shown on this page are general
representations of the door parts. Each specific door
models may have unique variations.
G2.
M1.
K3.
K2.
L1.
C4.
C2.
D1. D2.
C1.
K2.
NOTE: For Item (K2), The Rear Center Back Hang
Assemblies are to used for all doors over 11’0”
door height and over 14’0” door width. One Rear
Center Back Hang Assembly, per side.
NOTE: For Item (K3), The Rear Center Back Hang
Assemblies are to used for all doors over 16’0”
door height. Two Rear Center Back Hang Assem-
blies, per side.
H3.
H4.
H2.
B1.
A1.
F1.
F3.
F2.
C1.
A1.
H4.
F3.
F2.
F1.
H2.
B1.
H3.
C1.
N1.
N1.
L1.
D3.
J3.
J6. J5.
H1.
J4.
J7.
J9.
J1.
J10.
J5.
J8.
J2.
J5.
J6.
J5.
J5.
J3.
H1.
J8.
J1.
J5.
J4.
J7.
J10.
J2.
J11.
J11.
BREAKDOWN OF PARTS