background image

This Installation document is available at no charge from:
Wayne Dalton, a division of Overhead Door Corporation,
P.O. Box 67, Mt. Hope, OH., 44660, Or Online At 

www.Wayne-Dalton.com.

©Copyright 2016

REV5_09/20/2016

Part Number

T a b l e   O f   C o n t e n t s

347257

PLEASE DO NOT RETURN THIS PRODUCT 

TO THE STORE

If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the 
prompts to contact a customer service 
representative. They will be happy to handle 
any questions that you may have.

Pre-Installation 2

Important Safety Instructions 

2

Tools Required 

2

Package Contents 

2

Door Section Identification 

3

Removing an Existing Door 

4

Preparing the Opening 

4

Parts Breakdown 

6

Installation 7
Optional Installation 

18

Inside Lock 

18

Pull Down Rope 

18

Door Arm Hookup 

18

Maintenance 19

Cleaning Your Garage Door 

19

Operation And Maintenance 

19

Warranty 20

Wayne Dalton, a division of Overhead Door Corporation

Model 8700

T

o r s i o n

,   s

T a n d a r d

  L

i f T

W

i n d L o a d

i

nsTaLLaTion

 i

nsTrucTions

 a

nd

 o

Wner

s

 

M

anuaL

r

esidenTiaL

 

and

 L

ighT

 c

oMMerciaL

DEFINITION OF LIGHT COMMERCIAL:

1. Door heights less than or equal to 8’0” (< = 8’0”) are considered 
Residential applications.
2. Door heights greater than 8’0” (> 8’0”) are considered Light 
Commercial applications.

Wayne Dalton highly recommends that you read and fully understand 
the Installation Instructions and Owner’s Manual before you attempt this 
installation.

To avoid possible injury, read the enclosed instructions carefully before 
installing and operating the garage door. Pay close attention to all 
warnings and notes. After installation is complete, fasten this manual 
near garage door for easy reference.

IMPORTANT NOTICES!

Содержание 8700























Отзывы: