Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 195

Страница: 195 / 330

Flaw position calculation with angle probes

5 Operation

Krautkrämer USM 100

Rev. 9 (09/2023)

195

5.24 Flaw position calculation with

angle probes

You will find the functions for setting the flaw position
calculation when using angle probes in the function
group

Probe Angle

– In the A-scan tap on the

Probe Angle

icon to display

the function group.

Probe Angle

You can use the function

Probe Angle

to adjust the an-

gle of incidence of your probe for the material used. This
value is required for the automatic calculation of flaw po-
sition.

– In the

Measurement line

tap in the

Probe Angle

box.

– Set the probe angle

– couple the probe to the calibration block and calcu-

late the probe angle (see page 169).

The probe angle is displayed in the

Measurement line

Содержание Krautkramer USM 100










































































































































































































































































































































Результаты поиска

Содержание Krautkramer USM 100

Отзывы:

Waygate Technologies Krautkramer USM 100, Руководство по эксплуатации, Страница: 195 / 330

Результаты поиска

Содержание Krautkramer USM 100

Отзывы: