Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 330

Waygate Technologies Krautkramer USM 100 Скачать руководство пользователя страница 169

Defining the probe angle

5 Operation

Krautkrämer USM 100

Rev. 9 (09/2023)

169

5.18 Defining the probe angle

The function group

Probe Angle

provides all functions

to define the current index angle of a probe on a refer-
ence block. The current probe index angle is influenced,
e.g. by different materials or by the wear of the probe
contact face.

ATTENTION

You have to carry out calibration (see from
page 165) before defining the probe angle.

– After calibration, select the function group

(see page 156).

– Select

and choose the used calibration block.

– Check the values of

SDH Diameter

and

and correct them if necessary.

– Couple the probe to the calibration block.

– Position the gate on the calibration echo.

– In the Command bar tap on

(see page 74)

to execute the calculation.

The calculated angle is briefly displayed in the informa-
tion line at the bottom edge of the display screen.

«
...
167
168
169
170
171
...
»

Содержание Krautkramer USM 100











































































































































































































































































































































Отзывы:

Нет отзывов