manualshive.com logo in svg

WayCool WC-1HPMFAOSC, Руководство пользователя, Страница: 14 / 19

Поделиться
Скачать
WayCool WC-1HPMFAOSC Скачать руководство пользователя страница 14

Operation and Maintenance cont'd

REGULAR CLEANING

The frequency with which the WayCool® should be cleaned will depend on the environment in which it is used. The more dirty
the environment the more often it will need cleaning. 

In most cases the WayCool® will need to be cleaned weekly.

CAUTION The pads should be dry before you handle them, as they are stronger when dry than when they
are wet and less susceptible to damage. If they are wet, run the unit in the HIGH VENT position until they are
dry. After cleaning, let the pads air dry before you replace them.

1.

Turn the switch to OFF and unplug the unit.

2.

Remove the plastic retaining grates and check the pads for cleanliness. If they are dirty, remove and clean by spraying with
a garden hose (water only). If they are not dirty you will still need to remove the cooling pads to clean the inside of the unit.
Dirty cooling pads reduce the unit's effectiveness.

3.

Use a garden hose to rinse out the bottom and the inside of the unit. The dirt that accumulates is removed from the air
during operation, as the WayCool® also acts as an air filter.

4.

Remove the drain cap from the underside of the unit and let it drain completely. Rinse out any remaining dirt.

5.

Replace the drain cap (finger tighten only).

6.

Remove the pump discharge filter by unscrewing the top, removing the screen and rinsing it with a hose or under a tap.
Replace the filter screen and screw the top back on.

7.

Remove the pump filter from underneath the pump. Wash thoroughly with a hose. Compress filter and place back under
the pump.

8.

Replace the cooling pads once they are dry and re-install the plastic retaining grates.

With proper use and regular cleaning, the cooling pads will last about two seasons. If you handle them wet and are
abusive, however, they will be easily damaged. Refer to page 15 for recommended conditioning and cleaning
chemicals.

NORMAL STARTUP

1.

Place the unit where it will be run. Do not attempt to lift or move the unit once it is filled. Damage to the unit or a large spill
may occur.

When you decide where to place the unit, make sure there are no obstructions that could disrupt or block the airflow.
Make sure the unit is level at all times. Keep the unit at least three feet away from walls or other obstructions that will
interfere with airflow into the unit.

2.

Check the drain cap to be sure it is in place and secure.

3.

Connect the garden hose to the brass hose adapter. Be sure there is a washer in the female end of the hose connection.

4.

Open the water supply valve and be sure water enters the reservoir through the float valve by removing one cooling pad on
the side with the water connection. Allow the unit to fill and be sure the float valve shuts off the water completely.

5.

If you are filling the unit manually, remove the cap and fill the reservoir with a bucket or hose.

6.

Monitor the filling operation to avoid overflowing and damage. Watch the water level in the sight gauge.

7.

Plug the unit into a GFCI protected outlet.

8.

Adjust the spout to discharge cool air in the desired direction and tighten the knob on the end of the threaded rod.

9.

Turn the switch to the PUMP ONLY position and let it run for five to 10 minutes to saturate the cooling pads. Check that the
pads are saturated completely and there are no dry spots.

CAUTION Do not run the pump without water in the reservoir. The automatic shut-off feature is intended to
prevent operation of the pump without water, which can damage it or reduce its service life. Running the
pump dry will void the warranty on the pump.The red light indicates low water level (pump is off).

10. Turn the switch to the HIGH COOL or the LOW COOL position to begin normal cooling operation.

NORMAL SHUTDOWN

1.

Turn the switch to the HIGH VENT position and let the unit run until the cooling pads are dry. This will maximize the life of
the pads.

2.

Turn the switch to the OFF position. Unplug the unit if you are going to clean the pads or inspect the components.

3.

Shut off the water supply.

4.

Drain the reservoir if you are going to clean or store the unit.

5.

If the unit will be stored for the season, ensure the cooling pads are completely dry, and then remove them. Wrap them in
plastic bags or store them in a clean place where they will not be damaged or get dirty. The unit should be cleaned
thoroughly before storing.

13

netzerotools.com

netzerotools.com

Содержание WC-1HPMFAOSC




















Отзывы:

Нет отзывов