background image

 

DO NOT DRIVE WHILE DISTRACTED.

  Any function that requires your prolonged 

attention should not be performed while driving. Always stop the vehicle in a safe 
location before performing any such function. Failure to do so may result in an accident.

 KEEP THE VOLUME AT MODERATE LEVELS WHILE DRIVING. 

 Excess volume levels 

can obscure sounds such as emergency vehicle sirens or road warning signals and may 
result in an accident. Continuous exposure to high sound pressure levels may cause 
permanent hearing loss. Use common sense and practice safe sound.

 FOR USE WITH 12V NEGATIVE GROUND VEHICLE APPLICATIONS ONLY.

  Using this 

product  other than in its designed application may result in fire, injury or product 
damage.

MAKE THE CORRECT WIRING CONNECTIONS AND USE PROPER FUSE PROTECTION.

 

Failure to connect wiring correctly or use appropriate fuse protection may result in fire, 
injury or product damage . Ensure proper fusing of all system power wiring and install a 1-
ampere in-line fuse (not included) with the +12V lead to the unit’s power supply 
connector.

 

DISCONNECT THE NEGATIVE BATTERY TERMINAL BEFORE INSTALLATION.

 Failure 

to do so may result in fire, injury or damage to the unit.

 

D O NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.

 

Arrange wiring and cables to prevent obstructions when driving. Cables or wiring that 
obstruct or hang up on places such as steering wheel, brake pedals, etc. can be extremely 
hazardous.

 

DO NOT DAMAGE VEHICLE SYSTEMS OR WIRING WHEN DRILLING HOLES.

 When 

drilling holes in the chassis for installation, take precautions so as not to contact, 
puncture or obstruct brake lines, fuel lines, fuel tanks, electrical wiring, etc. Failure to 
take such precautions may result in fire or an accident.

 

DO NOT UTILIZE OR CONNECT TO ANY PART OF VEHICLE SAFETY SYSTEMS.

 Bolts, 

nuts or wires used in the brake, airbag, steering or any other safety-related systems or 
fuel tanks should NEVER be used for mounting, power or ground connections. Using such 
parts may disable control of the vehicle or result in fire.

 WARNING

 WARNING

This symbol means important instructions. 
Failure to heed them can result in serious injury or death.

 CAUTION

This symbol means important instructions. 
Failure to heed them can result in injury or property damages. 

1

 CAUTION

 

STOP USE IMMEDIATELY IF A PROBLEM OCCURS. 

Failure to do so may result in 

personal injury or damage to the product. Return it to your authorized Wāvtech dealer

.

 HAVE AN EXPERT DO THE WIRING AND INSTALLATION. 

This unit requires special 

technical skill and experience for wiring and installation. To insure safety and proper 
fun

ction, always contact the authorized dealer where you purchased the product to have 

it done professionally.

  

INSTALL THE UNIT SECURELY WITH SPECIFIED PARTS. 

Be sure to use only the 

included parts and specified installation accessories (not included). Use of other than 
designated parts may damage this unit.  Install the unit securely so that it will not come 
loose during a collision or sudden jolt.

Содержание LinkT













Отзывы: