background image

SPK IN

REM OUT

RCA OUT

+12V

GND

RLC

bassRESTOR

EFFECT

BASS PROCESSOR

80

30

50

MED

NAR

WIDE

MID

MIN

MAX

15

50

30

REM OUT

SPK IN

RCA OUT

+12V

GND

RLC

bassRESTOR

EFFECT

BASS PROCESSOR

80

30

50

MED

NAR

WIDE

MID

MIN

MAX

15

50

30

 

Installation & System Wiring

 It is important to read this manual thoroughly before starting your installation and always plan 
accordingly. Before installing any Wāvtech product, disconnect the negative (ground) wire from the 
vehicle’s battery to avoid damage to the vehicle or yourself. Following all guidelines will help provide 
years of enjoyment with your Wāvtech bassRESTOR audio interface.
Ground Connection (GND):  The GND terminal must be connected to a metal part of the vehicle that is 
welded to the vehicle body with ground plane back to the main battery ground attachment point (a.k.a. 
chassis ground). This wire should be a minimum of 18AWG and as short as possible to minimize potential 
for noise to enter the system. The chassis ground connection point should have all of the paint removed 
and be scuffed to the bare metal. The ground wire should be terminated by a ground specific interlocking 
terminal such as the included EARL terminal or ring terminal securely bolted to the vehicle with star or 
lock washer and nut to prevent from coming loose.  Avoid using factory ground points to reduce the 
chance of induced noise from other components.
Power Connection (+12V):  The constant power connection should be made at the vehicle battery when 
possible. For direct battery connection, a 1-amp fuse must be installed in-line with the power wire within 
18”of the battery and securely connected to the positive battery terminal bolt with a ring terminal. If 
connecting to another available co12V power source, a 1-amp in-line fuse must be added at the 
connection point. The power wire should be a minimum of 18AWG. Do not install the fuse until all other 
system connections have been made.
Speaker Level Input (SPK):  Connect the speaker wires from the source unit to corresponding terminals on 
the interface. Use the SPK input if your source unit is not equipped with RCA outputs. Always ensure the 
correct polarity of each channel when making these connections, as failure to do so can severely effect 
sound performance.
Remote Input (REM IN):  If the source unit has a remote output wire (pr12V only when turned on), 
connect it to the REM IN terminal. If a remote lead is unavailable, all Wāvtech interfaces also provide 

 

automatic turn-on via DC-offset and audio signal detection. While auto turn-on will work in most 
applications, there may be some cases were a +12V trigger is needed for satisfactory results. These signal 
detect functions can also be individually defeated via internal jumpers (labeled DC and AUD) if necessary.
Remote Output (REM OUT): Use the remote output to provide a +12V trigger to turn on amplifiers or 
other components. This +12V output is generated internally by the interface when turned on either by 
REM IN or signal sensing, and will provide over 500mA of constant current for external devices.
Remote Level Control (RLC):  Connect the remote to the bassRESTOR’s RLC port with the supplied 
16.4ft/5m cable. Plan cable routing before mounting the remote to ensure proper length. If additional 
length is required, a standard 8-conductor CAT5 or CAT6 ethernet cable or extension may be used. The 
cable may also be shortened and re-terminated with a RJ45 connector and ethernet crimping tool.  

Example-1: Speaker Level Input from OEM Radio

System Examples

Note:  In vehicles where the factory radio has a fixed level or digital output to a factory amplifier, signal for the 
bassRESTOR’s speaker level input should be connected at the amplifier’s output.  

Example-2: Speaker Level Input from OEM Amplifier

Note:  When using a receiver’s internal power IC to drive speakers directly, note that its speaker outputs will likely clip 
below the maximum master volume level. Adjust gain settings accordingly for optimum unclipped volume range.

3

Содержание bassRESTOR









Отзывы: