Wavelength Electronics PLD10000 Скачать руководство пользователя страница 20

© 2020

www.teamWavelength.com

20

PLD10000/PLD12500 LASER DIODE DRIVER

CERTIFICATION AND WARRANTY

CERTIFICATION

Wavelength  Electronics,  Inc.  (Wavelength)  certifies  that  this 

product met its published specifications at the time of shipment. 

Wavelength further certifies that its calibration measurements are 

traceable to the United States National Institute of Standards and 

Technology, to the extent allowed by that organization’s calibration 

facilities, and to the calibration facilities of other International 

Standards Organization members.

WARRANTY

This Wavelength product is warranted against defects in materials 

and workmanship for a period of one (1) year from date of shipment. 

During the warranty period, Wavelength will, at its option, either 

repair or replace products which prove to be defective. 

WARRANTY SERVICE

For warranty service or repair, this product must be returned to the 

factory. An RMA is required for products returned to Wavelength 

for warranty service. The Buyer shall prepay shipping charges to 

Wavelength and Wavelength shall pay shipping charges to return 

the product to the Buyer upon determination of defective materials 

or workmanship. However, the Buyer shall pay all shipping 

charges, duties, and taxes for products returned to  Wavelength 

from another country.

LIMITATIONS OF WARRANTY

The warranty shall not apply to defects resulting from improper 

use or misuse of the product or operation outside published 

specifications.  No  other  warranty  is  expressed  or  implied. 

Wavelength  specifically  disclaims  the  implied  warranties  of 

merchantability and fitness for a particular purpose. 

EXCLUSIVE REMEDIES

The remedies provided herein are the Buyer’s sole and exclusive 

remedies. Wavelength shall not be liable for any direct, indirect, 

special, incidental, or consequential damages, whether based on 

contract, tort, or any other legal theory.

REVERSE ENGINEERING PROHIBITED

Buyer, End-User, or Third-Party Reseller are expressly prohibited 

from reverse engineering, decompiling, or disassembling this 

product.

NOTICE

The information contained in this document is subject to change 

without notice. Wavelength will not be liable for errors contained 

herein or for incidental or consequential damages in connection 

with the furnishing, performance, or use of this material. No part of 

this document may be translated to another language without the 

prior written consent of Wavelength.

SAFETY

There are no user-serviceable parts inside this product. Return the 

product to Wavelength Electronics for service and repair to ensure 

that safety features are maintained.

LIFE SUPPORT POLICY

This important safety information applies to all Wavelength 

electrical and electronic products and accessories:

As a general policy, Wavelength Electronics, Inc. does not 

recommend the use of any of its products in life support applications 

where the failure or malfunction of the Wavelength product can 

be reasonably expected to cause failure of the life support device 

or  to  significantly  affect  its  safety  or  effectiveness.  Wavelength 

will not knowingly sell its products for use in such applications 

unless it receives written assurances satisfactory to Wavelength 

that the risks of injury or damage have been minimized, the 

customer assumes all such risks, and there is no product liability 

for Wavelength. Examples of devices considered to be life support 

devices are neonatal oxygen analyzers, nerve stimulators (for 

any  use),  auto-transfusion  devices,  blood  pumps,  defibrillators, 

arrhythmia detectors and alarms, pacemakers, hemodialysis 

systems, peritoneal dialysis systems, ventilators of all types, and 

infusion pumps as well as other devices designated as “critical” 

by the FDA. The above are representative examples only and are 

not intended to be conclusive or exclusive of any other life support 

device.

REVISION HISTORY

DOCUMENT NUMBER: PLD10000-0400

REV.

DATE

CHANGE

F

3-Sep-2012

Updated pin specifications

G

January 

2013

Update for Product Revision D

H

November 

2013

Added CE mark and extended 

warranty

I

March 2015

Added airflow direction

J

October 

2015

Added Disable Fall Time 

specification

K

Nov. 2015

Removed relay short from 12.5 A

L

April 2020

Updated noise section

51 Evergreen Drive

Bozeman, Montana 59771

406-587-4910  (tel)

406-587-4911  (fax)

Sales & Tech Support

[email protected]

[email protected]

Содержание PLD10000





















Отзывы: