background image

Hardware 

Installation Manual

Page 14

Installing the LCU

Each ROME Chassis is controlled by an LCU. The LCU install kit includes the LCU, a signaling cable (Y-Cable) 
to attach to the ROME Chassis, and a ground cable. 1 RU of space above the LCU is recommended to allow 
adequate space for connecting the LCU control and ground cable. 

Installing the LCU involves the following steps:

1.    Mounting the LCU 
2.    Connecting Cables (signalling and ground)
3.    Powering up ROME by plugging in both power cables

5.1 

Mounting the LCU

The LCU mounting kit comes with two L-brackets (ears) which are attached to the front of the LCU chassis and 
extension brackets in the back that is mounted on the rear post to support the LCU chassis. To install the LCU,  
slide the LCU into position, and secure the brackets to the rack.

The LCU should be installed on top of the ROME Chassis. 

5.2 

Connecting Cables (Signaling and Grounding)

5.2.1    Connecting the Signaling Y Cable

To connect the LCU to the ROME Chassis, the following steps should be taken:

 

1.    Connect the ROME signaling Y cable to the LCU output 

Backside of LCU with Signaling Y cable connected

Содержание Fiber Smart Networks ROME 128Q























Отзывы: