background image

EN

14

15

Wave products have been inspected with no evident defects prior to leaving the

factory.

Wave warrants this product against defects in material and workmanship for a period of time, 

Warranty for this product begins on the date of purchase and Wave requires presen-

tation of the original proof to purchase to confirm the date. During the warranty period,

Wave will either repair or replace, at its discretion, any defective products. Replace-

original warranty.

Shipping cost policy

The return of defect parts to the authorized service centre is at the cost of the owner.

On warranty period, the return is at the cost of service center.

Warranty policy

This limited warranty does not apply to any defect resulting from negligence, accident,

misuse, or other reason beyond Wave’s control, included but not limited to:

normal wear and tear, negligence or failure to follow the product instructions, improper

or inadequate maintenance; connection to improper power supply; chemical water

This warranty is valid only in the country of purchase in such countries where Wave

Warranty service outside the country of purchase is limited to the terms and conditions

of the corresponding warranty in the country of service. Where the cost of repairs or

replacement is not covered by this warranty, Wave will advise the owners and the cost

shall be charged to the owner.

This warranty only applies to the original purchaser and terminates upon any transfer of

ownership.

All repairs of which warranty claims are made must be pre-authorized by a Wave

service centre.

your Wave product. Wave will not be liable for results of cost of workmanship from

unauthorized service person.

Warranty registration

To validate your warranty, please register your product on our website Wave:www.wavespas.com

It is essential that all informations including customer name, date of

purchase, serial number, spa model are provided. Without this information the warranty 

will be invalid.

7. WARRANTY

7.2. Warranty

If the screen displays an error code “Ex”, please refer to the table below.

E3, E4, E5, E6 error code

If error code is still displayed on the control Box, please do the following instructions: 

1 - Check that the water line is between the high and low limits.

3 - Unscrew and clean the 2 nozzles (Entry and exit of water) inside the spa and remove  wastes if necessary (leaves, hairs, fur,

skin...)

 foreign objects.

Cut the spa again electrically for 5 minutes and re-connect it, if the error code is still displayed on the control box please contact 

the service centre.

7.1. Error code

Code Situation

Problem

Cause

S

s

olutions

E1 Not heating Not 

heating properly.

Wrong temperature 

control sensor.

Temperature control sensor short 

circuit or open circuit.

Contact service center.

E3 Not heating 

properly.

High water tempera-

ture indicator.

E4

All functions do 

not work, buzzing 

warning.

Low water tempera-

ture indicator.

The pool water is lower than 2°C 

(36°F).

water is between 2°C~44°C (36°F~111°F)

· If this does not solve the problem, refer 

to the box below

E5

All functions do 

not work, buzzing 

warning.

High water tempera-

ture indicator.

(122°F).

-

cian to reset the thermal cutout described 

in next paragraph. 

· If this does not solve the problem, refer 

to the box below

E6

Not heating and 

Buzzing warning.

Water pressure is 

not big enough to 

activate heating.

·Inlet or outlet on inner wall are 

blocked.

·Filter cartridge is too dirty.

·Pool water does not reach mini-

mum water level.

·Do not release air from pump 

Pump is wrong”

·Clean inlet and outlet

·Add water to reach water level

·Do air release as outlined again

· If this does not solve the problem, refer 

to the box below

1. The filled water is over 45°C

   (113°F)

2.The filter cartridge was put on the wrong 

suction fitting (higher suction fitting).

2.Put the filter cartridge on the lower suction 

fitting.

1.Cut off the power,make sure the pool water is

between 2°C~44°C(36°F~111°F).If this does not 

solve the problem, refer to the box below.

Waves Direct

121 New Bridge Street, Newcastle upon Tyne,

Tyne and Wear, NE1 2SW, United Kingdom 
wavespas.com

Содержание ROME










Отзывы: