manualshive.com logo in svg

Wave NCBSLXE2, Инструкция по установке и эксплуатации

Поделиться
Скачать
Wave NCBSLXE2 Скачать руководство пользователя страница 15

SPEEDLAN Installation and Operation User Guide

     

Quick Start

2-3

                                                                                                                                                              

•

*Wire zip ties 

•

*Antenna (specialized upon request) 

•

*Amplifier (specialized upon request) 

* Note:

    Items can be purchased separately or as part of an Installation Kit. 

  

Installation Steps 

Installation instructions are specific to customers who purchased Installation Kits from Wave 
Wireless. To view a diagram of the installation listed below, see 

Installation Diagram, page 2-7

. 

The directions below contain installation procedures for the items included in the SPEEDLAN brouter 
antenna (and amplifier) kit. If you do not have an item included in the instructions below, contact 
Wave Wireless. 

If you are having trouble and need a full site installation, contact Wave Wireless Networking for 
services and fees. 

To install the SPEEDLAN, do the following: 

Step 1. Line of Sight

Before installing the antennas and bridges, make sure a clear line of sight exists. Line of sight can be 
defined as each antenna being able to clearly see the other antenna or being able to see the remote 
locations when viewing from the SPEEDLAN base station location. Be sure to look level with the 
center of origin of the transmission (the middle of the antenna). Do the same from the remote 
location. Any disruption of the signal path due to trees, buildings or any other obstructions may 
cause the link to function improperly. If you see any such obstruction between the two antennas, 
move one or both antennas elsewhere.

Step 2. Mount the Antenna

a)

  On a side building mount, as in the diagram at the end of this section, position the bracket 

so there will be at least three feet (one meter) above the roof line of the building where the 

pole is attached; this leaves room for the antenna and reduces signal loss from building 

reflection. 

TIP

Содержание NCBSLXE2
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды