Wave NCBSLXE2 Скачать руководство пользователя страница 10

Страница: 10 / 95

SPEEDLAN Installation and Operation User Guide

1-4

Introduction

Features

•

10/100BASE-T Ethernet Interface

•

SPEEDLAN 11 Mb Wireless Radio Interface

•

Bridging Features

•

Protocol Transparent Bridging

•

IP Routing

•

Filtering by Ethernet Multicast, Broadcast and Bad Packets

•

Filtering by Protocol

•

Filtering by Ethernet Address Pair

•

Generic Ethernet Tunneling through IP Networks

•

Learned Table Lockdown

•

Expanded IP ARP Support

•

Automatic Broadcast Storm Protection and Notification

•

Supports up to 48 Remote Buildings

SNMP Features

•

IP "ping" Support

•

IP SNMP Support (MIB II, Ethernet, Interface, SNMP, and Bridge MIB)

•

IP SNMP WaveLAN

•

IP SNMP Trap Support

•

SNMP Access Lists

ISP Features

•

DHCP Server

•

Outgoing and Incoming NAT

SNMP Management

SNMP wireless and wired link management may be administered from any Ethernet network or
remotely from the Internet. The SNMP MIB II, Bridge MIB, and Ethernet-Interface MIB come with the

Содержание NCBSLXE2
































































































Результаты поиска

Содержание NCBSLXE2

Отзывы:

Бренды по названию

Популярные бренды

Wave NCBSLXE2, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NCBSLXE2

Отзывы:

Бренды по названию

Популярные бренды