manualshive.com logo in svg

wattstopper LP Series, Справочник по установке и подключению

Поделиться
Скачать
wattstopper LP Series Скачать руководство пользователя страница 6

Visit our web site for FAQs: www .wattstopper .com

14.5"

(368.3 mm)

12.53"

(318.3 mm)

Slotted

Mounting

Holes

16.5"

(419.1 mm)

15.08"

(383.0 mm)

Line V

oltage Compartment

(High V

oltage)

6"

(152.4 mm)

Low Voltage Compartment

(Class 2)

Figure 3: LP8 Enclosure dimensions, mounting holes, location of line and low voltage wiring compartments

/RZ9ROWDJH&RPSDUWPHQW

&ODVV

PP

PP

PP

/LQH9ROWDJH&RPSDUWPHQW

+LJK9ROWDJH

PP

PP

PP

/RZ9ROWDJH
%HUH

Figure 4: LP24 Enclosure dimensions, mounting holes, location of line and low voltage wiring compartments

Install Interior

Do not reinstall the interior until after the exterior enclosure has been securely mounted to the wall and the 

conduit/wiring holes have been drilled or knocked out. 

1.  Place the interior in the enclosure. 
2.  Align the interior with the studs provided in the enclosure. 
3.  Hold the interior in place while you pull up on the black self-retaining pop-fasteners to open the door. 
4.  Replace the washers and tighten down the nuts removed in 4b of the mounting process. 
5.  Attach the transformer mounting assembly to the back of the enclosure using the washer and nut 

removed in 4a of the mounting process.

6.  Close the interior door and push in the pop-fasteners.

6

Содержание LP Series













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды