background image

Unit aDJUStMent

A “configuration” button allows access to the 

WattStopper Push n’ Learn™ technology to 

change the operation of the LMRH-101 .

Step 1: enter push n’ Learn (pnL)

a . Locate the configuration button inside the 

LMRH-101 battery compartment . 

b . Point the LMRH-101 at a DLM IR device . 
c . Press and hold the configuration button 

until the red LED in the battery compartment begins blinking 

(approximately 3 seconds), then release the button . Make sure the 

LMRH-101’s red LED continues to blink, then observe the following:

-  The Red LEDs on all other DLM devices on the network start blinking 

rapidly (2x/second) . The LEDs continue to blink until you exit PnL . 

-   All loads on the DLM local network turn OFF immediately after entering 

PnL . After 1 second, load 1 turns ON .  

Step 2: Load Selection

A quick press on the LMRH-101’s configuration button turns OFF load 1 

then turns on the next load in sequence . Keep pressing the configuration 

button to step through all the loads connected to the DLM local network . 

When a load turns ON the blue LED is lit brightly on all switch buttons and 

sensors bound to the load . 
-  To bind the load to the LMRH-101: While the load is ON press the 

paddle making sure that the blue LED turns ON brightly . 

-  To unbind a load: While the load is ON and the blue LED is brightly 

lit, press the paddle . The LED goes dim to indicate the paddle on the 

handheld remote no longer controls this load . 

-  A quick press on the configuration button turns ON the next load . 
-  Repeat until the paddle is bound to all the loads you want it to control .

  note:

 more than one load can be assigned to the paddle and a load can 

be assigned to multiple devices in the DLM network .

Step 3: exit push n’ Learn (pnL)

a . Point the LMRH-101 at a DLM IR device . 
b . Press and hold the LMRH-101 configuration button until the red LED 

in the battery compartment stops blinking (approximately 3 seconds), 

then release the button . 

Point at

DLM Device

Configuration

Button

Red LED

Содержание LMRH-101

Страница 1: ...eration UNIT DESCRIPTION The WattStopper LMRH 101 Digital IR Handheld Remote uses an infrared IR transmitter to send commands to a Digital Lighting Management DLM network It allows the user to turn lights ON OFF and dim without going to a wall box device The LMRH 101 operates on three AAA batteries It communicates wirelessly with other DLM devices by sending an IR signal to a DLM IR enabled device...

Страница 2: ...ess the top of the rocker paddle to turn load s ON The blue LED on the paddle also turns ON Switched loads turn ON Dimmable loads turn ON to the last light level set before they turned OFF Press the bottom of the rocker paddle to turn load s OFF Dimmable loads ramp down or up in response to pressing and holding the top or bottom of the paddle ON OFF loads turn OFF when the ramp level dims below 50...

Страница 3: ...ext load in sequence Keep pressing the configuration button to step through all the loads connected to the DLM local network When a load turns ON the blue LED is lit brightly on all switch buttons and sensors bound to the load To bind the load to the LMRH 101 While the load is ON press the paddle making sure that the blue LED turns ON brightly To unbind a load While the load is ON and the blue LED...

Страница 4: ... the DLM local network to PnG using the LMRH 101 1 Point the LMRH 101 at an IR enabled DLM local network device 2 Press and hold the configuration button in the battery compartment until the red LED starts blinking to put the DLM local network into PnL see Step 1 in UNIT ADJUSTMENT for details Release the button 3 Press and hold the configuration button again for approximately 20 seconds until the...

Отзывы: