Watts tekmar 681 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 20

Watts tekmar 681 Скачать руководство пользователя страница 5

5

Depress the two snaps

on the bottom of the

enclosure to release the

front cover.

Secure enclosure using four #6 or #8

wood screws.

Install the front cover by

hooking the top catches

and pivoting the cover

into place.

Installing the Enclosure

Installation Using Mount Holes and Screws

Mounting Screw

Snap the enclosure onto

35mm DIN rail using the

hooks and snaps on the

back of the enclosure.

Location of DIN rail hooks

and snaps on the back of

the enclosure.

Latch top hooks of

enclosure onto DIN rail.

Then rotate enclosure

down engaging bottom

snaps.

Enclosure mounted on

DIN rail (back view).

Low-Voltage Wiring

Pull two conductor 18 AWG cable, up to 500 feet

(150 m) long, for the following equipment:

• Outdoor temperature sensor (Optional)

Pull four solid conductor 18 AWG cable, up to 500 feet

(150 m) long, for the following equipment:

• Snow Sensor 095

Pull five solid conductor 18 AWG cable, up to 435 feet

(132 m) long, for the following equipment:

• Snow / Ice Sensor 090

Rough-In Wiring

To prevent the risk of personal injury and/or death, make sure power is not

applied to the interface until it is fully installed and ready for final testing . All work

must be done with power to the circuit being worked on turned off .
Please be aware local codes may require this interface to be installed or

connected by an electrician .

DIN Rail Mounting

«
...
3
4
5
6
7
...
»

Содержание tekmar 681





















Отзывы:

Нет отзывов