background image

7

1.   Using a smart phone or tablet, 

scan the QR code on the side 

on the Wireless Node, or go to 

https://connected.syncta.com.

2.   When prompted, enter the 

Device ID. The Device ID is a 

15-digit number found beneath 

the QR code on the side of the 

Wireless Node.

3.   Follow onscreen prompts to 

create a Syncta account, or 

if you are an existing Syncta 

user, log in to your account. 

The device can be registered 

to multiple accounts.

4.   Once the device is regis-

tered to your account, follow 

prompts to add notifications.

 

 To manage alerts, login to your 

account on Syncta.com.  

Wireless Node Operation

1.  

Start-Up

 – Upon start-up, the Power LED (7) will light up 

a steady green to indicate power is supplied. The Wireless 

Node will automatically go into its start-up sequence. During 

the start-up sequence, the light over the Program button 

(5) will begin as solid white and then change to a blinking 

green, indicating the Wireless Node is searching for a cellu-

lar connection. Once a cellular connection is established, the 

Program button light will start blinking cyan, indicating that 

the Wireless Node is connecting to the Cloud. Once a Cloud 

connection is established, the Program button light will blink 

rapidly for a few seconds, and then shut off. The Cellular 

LED (8) and IoT LED (9) should both be a solid blue.

2.  

Cellular Connection

 – Once the start-up sequence is 

completed, the Cellular LED will be a steady blue if there is 

a good connection. It will blink if there is a poor connection. 

There will be no color if there is no connection.

3. 

 IoT  Connection

 – If there is a Cloud connection, the IoT 

LED will be a steady blue. There will be no color if it is off.

NOTICE

If there is no Cloud connection, then notifications will not be 

sent to the user via Syncta.

4.  

Flood LED 

– If a flood event occurs, the Flood LED (10) 

will be a steady orange. It will remain on so long as there 

is a flood condition.

5.  

Test Button

 – When Cellular and Cloud connections 

have been made, a test message can be sent through the 

Syncta app by pressing the Test Button (3).

6.  

Reset Button

 – You can reset the Wireless Node and 

restart the start-up sequence by pressing the Reset but-

ton (4).  This will cause all on-going operations to cease.

7. 

 Program  Button

 – The Program button (5) should not be 

pressed and is for factory use only.

Installation and Operation

Registering Your Device and Alert Confi guration

Содержание SentryPlus 113RFP









Отзывы: