Watts PVi CENTURION Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 131

background image

Centurion Water Heater- Edge [ii]: Install-Operation-Service

SECTION 10: TROUBLESHOOTING

OMM-0153_A

• 8/25/2022 Technical Support • (800) 526-0288 • Mon-Fri, 8 am - 5 pm EST Page 111 of 131

Centurion Troubleshooting Procedures

Fault

Probable Causes

Corrective Action

3.

Defective Air/Fuel Valve
stepper motor.

3.

Replace stepper motor.

4.

Defective Power Supply
Board or fuse.

4.

Check DS1 & DS2 LEDs on Power Supply Board. If
they are not steady ON, replace Power Supply
Board.

5.

Defective IGST Board.

5.

Check “Heartbeat” LED DS1 and verify it is blinking

ON & OFF every second. If not, replace IGST Board.

6.

Air/Fuel Valve out of
calibration

6.

Perform the stepper motor calibration procedure
(Main Menu

→

Diagnostics

→

Subsystems

→

Air

Fuel Valve Stepper Motor).

10.2 ADDITIONAL FAULTS WITHOUT SPECIFIC FAULT MESSAGES

Refer to Table 12.2 to troubleshoot faults which may occur without a specific fault message
being displayed.

TABLE 12.2: Water Heater Troubleshooting with No Fault Message Displayed
Observed
Incident

Probable Causes

Corrective Action

Hard Light-Off

1.

Clogged/damaged Gas
Injector on Igniter-
Injector (Figure 7.2-1).

1.

Disconnect the Staged Ignition Assembly solenoid from the
Gas injector Tube of the Igniter-Injector (Figure 7.2-1) and
inspect Gas Injector to ensure it is not clogged or damaged.

2.

Defective Staged Ignition
Solenoid (Figure 7.2-1).

2.

Close the Manual Shutoff Valve. Attempt to start the unit

and listen for a “clicking” sound that the Staged Ignition
Solenoid makes during Ignition Trial. If “clicking” sound is

not heard after 2 or 3 attempts, replace the Staged Ignition
Solenoid.

Fluctuating
Gas Pressure

1.

Gas pressure going into
unit is fluctuating.

1.

Stabilize gas pressure going into unit. If necessary,
troubleshoot Building Supply Regulator.

2.

Damping Orifice not
installed.

2.

Check if the gas train is supposed to have a Damping
Orifice, and if so, ensure that it is installed in the SSOV
Actuator, as shown in Figure 10.2-3, below.

«
...
109
110
111
112
113
...
»

Содержание PVi CENTURION




































































































































Отзывы:

Нет отзывов

Похожие инструкции для PVi CENTURION

Бренд: Eastern Tabletop Страницы: 19

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Waterfall Kit WFK8

Бренд: Beckett Страницы: 1

Бренд: LAGO Страницы: 6

Бренд: Oase Страницы: 70

Corken Z-Series

Бренд: Idex Страницы: 32

Бренд: T.I.P. Страницы: 112

ELITE SUBMERSIBLE

Бренд: Hagen Страницы: 2

Бренд: Reznor Страницы: 31

Бренд: WaterGroup Страницы: 24

Alaris CC Guardrails 80033UND1-G

Бренд: CareFusion Страницы: 40

Бренд: vitapur Страницы: 36

Бренд: Kospel Страницы: 12

Бренд: Master Страницы: 129

PureBallast 135 Compact USCG

Бренд: Alfa Laval Страницы: 412

Бренд: German pool Страницы: 7

LABOPORT N 810 FT.18

Бренд: KNF Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды