![background image](http://html1.mh-extra.com/html/watts/pvi-aqua-solve-family/pvi-aqua-solve-family_installation-manual_3928863004.webp)
IMPORTANT: INSTALLATION AND
SAFETY INFORMATION
Follow the installation instructions carefully. Failure to install the
softener properly may void the warranty.
Use care when handling the softener. Do not turn upside down, drop, or
set on sharp protrusions.
Before you begin installation, read this entire manual. Then obtain all the
materials and tools you will need to make the installation.
Check local plumbing and electrical regulations and byelaws.
The installation must conform to them.
Do not locate the softener where freezing temperatures occur. Do not
attempt to treat water over 49ºC.
Freezing or hot water damage
will void your warranty.
Avoid installing in direct sunlight. Excessive sun heat may cause
distortion or other damage to non-metallic parts.
Maximum allowable inlet water pressure is 4.76 bar.
If the daytime pressure exceeds 4.76 bar, a pressure reducing valve is
recommended (adding a pressure reducing valve may reduce the flow).
The softener works on
24 volt 50 Hz electrical power only.
Be sure
to use the supplied transformer and plug it into a normal 240V, 50Hz
household outlet that is in a
dry location only
, grounded and properly
protected by an over current device such as a circuit breaker or fuse.
This softener is not intended to be used for treating water that is
microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system.
LEAD PIPEWORK
Where lead pipework exists downstream of the proposed location of the
water softener, we advise you ask the local water authority for advice
on the replacement of lead pipework.
European Directive 2002/96/EC requires all electrical and
electronic equipment to be disposed of according to Waste
Electrical and Electronic Equipment (
WEEE RM05711
)
requirements.
IMPORTANT: INSTALLATION AND
SAFETY INFORMATION
Follow the installation instructions carefully. Failure to install the
softener properly may void the warranty.
Use care when handling the softener. Do not turn upside down,
drop, or
set on sharp protrusions.
Before you begin installation, read this entire manual. Then obtain all the
materials and tools you will need to make the installation.
Check local plumbing and electrical regulations and byelaws
.
The installation must conform to them.
Do not locate the softener where freezing temperatures occur.
Do not
attempt to treat water over 49ºC.
Freezing or hot water damage
will
void your warranty
.
Avoid installing in direct sunlight. Excessive sun heat may cause
distortion or other damage to non-metallic parts.
Maximum allowable inlet water pressure is 4.76 bar.
If the daytime pressure exceeds 4.76 bar, a pressure reducing valve is
recommended (adding a pressure reducing valve may reduce the flow).
The softener works on
24 volt 50 Hz electrical power only
. Be sure to
use the supplied transformer and plug it into a normal 240V,
50Hz
household outlet that is in a
dry location only
, grounded and prop-erly
protected by an over current device such as a circuit breaker or fuse.
This softener is not intended to be used for treating water that is
microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system.
LEAD PIPEWORK
Where lead pipework exists downstream of the proposed location of the
water softener, we advise you ask the local water authority for advice
on
the replacement of lead pipework.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by EcoWater Systems
could void the user’s authority to operate the equipment.
European Directive 2002/96/EC requires all electrical and
electronic equipment to be disposed of according to Waste
Electrical and Electronic Equipment (
WEEE RM05711
)
requirements.
Please Remember
–
Only use tablet or pellet salt in your softener!
4
4
Содержание PVI Aqua Solve Family
Страница 1: ...INSTALLATION MANUAL Aqua Solve Family AQS 9 Aqua Solve Large AQS 14 400498 05 15...
Страница 14: ...14 NOTES...
Страница 15: ...NOTES 15...
Страница 16: ......