Watts AERCO KC Series страница 21 Скачать руководство пользователя

Страница: 21 / 82

CONTROL PANEL OPERATING PROCEDURES

Figure 3.11

Proof of Closure Switch Location

Figure 3.12

Air/Fuel Valve Open and Engaging the Air/Fuel

Valve Open Microswitch

7. At the end of the purge cycle the combustion

safeguard initiates a 10 second trial for
ignition and the following simultaneously
occurs:

The LCD displays the message IGNITION

TRIAL.

The ignition transformer energizes.

The air/fuel valve rotates to its low fire

position. This engages the air-fuel valve
closed switch, energizing the safety shut-off
valve, (see Fig. 3.14).

Figure 3.13

Blower Proof Switch Location

8. Once the combustion safeguard detects

flame, its flame LED lights. Power is
removed from the ignition transformer and
the MAIN LED lights of the combustion
safeguard.

At this point, the annunciator will display FLAME
PROVEN. The unit, provided it is in the
automatic mode, is released to modulate and
will be controlled by the temperature control
system.

Figure 3.14

Air/Fuel Valve in Ignition Position, Engaging the

Ignition Microswitch

CONNECTOR

149

VALVE

SHUT-OFF

SAFETY

SWITCH

CLOSURE

PROOF OF

148

145

146

147

FROM

Содержание AERCO KC Series



















































































Результаты поиска

Содержание AERCO KC Series

Отзывы:

Похожие инструкции для AERCO KC Series

Бренды по названию

Популярные бренды

Watts AERCO KC Series, Руководство пользователя

Результаты поиска

Содержание AERCO KC Series

Отзывы:

Похожие инструкции для AERCO KC Series

Бренды по названию

Популярные бренды