![background image](http://html.mh-extra.com/html/watts/68101336/68101336_installation-operation-and-maintenance-manual_877081004.webp)
4
NOTICE
Please confirm that all items required are included in the kit ready
for assembly and remove from carton.
1. The system can stand upright in the desired location without
the need to affix to a wall.
2. Place the system in the desired location. Make sure that the
location is level and sturdy enough to support the weight of the
wetted system.
3. Turn off the main water supply to the home and open an inside
faucet to relieve any pressure within the plumbing system.
4. Install a supply valve (user supplied) in the supply line and close it.
5. Take the two 1" NPT (Item 2 below) threaded adapters and
apply PTFE plumbing tape to the plumbing adapter threaded
ends. Install first the union nut, white split ring then the o-ring
onto each plumbing adapter. Place the threaded adapters into
the bypass valve (Item 1) as shown in Diagram A.
6. Secure the adapters with the nuts on the threaded connections
on the bypass valve. Hand Tighten Only. Do Not use PTFE tape
on the threaded ports of the bypass valve assembly.
7. Attach the bypass valve (Item 1 below) to head assembly shown
in Diagram A on the E-Treat system. Do Not use PTFE tape on
the threaded ports of the head assembly.
8. Secure the bypass to the head with nuts on bypass. Hand
Tighten Only.
9. Place the bypass into the Service Operation Position.
10. Connect the cold water supply to the inlet of the E-Treat system.
11. Connect the outlet of the E-Treat system to the supply line
going into the home.
Bypass Valve
NPT Threaded Inlet/Outlet
Adapters (x2)
Installation Instructions
The new system comes with the media, bypass, and tail pieces in the
carton. Installer should verify this prior to installation. How to install
your E-Treat system can also be found at www.PremierH2O.com.
1
2
E-Treat Parts
Diagram A
ByPass Operation
Supply Water
Enters
Water Supply
Exits
Service Operation
Supply Water
Enters
Water Supply
Exits
Start Up
1. Remove the dome plug at the top of the tank so most of the air
can vent from the tank during its initial fill with water.
2. Open the nearest cold water side of a faucet.
3. Turn water on at main supply line slowly and open the newly
installed supply valve to 1/4 open position. Inspect systems for
leaks. If leaks are present, repair immediately before proceeding.
4. Allow tank to fill with water until the water level in the tank can
be seen through the dome hole port. Then reinstall the dome
hole plug and hand tighten it into the top of the tank.
5. Close the cold faucet, put the system in bypass mode and fully
open the supply valve. Allow the tank to sit for 24 hours before
finalizing the startup procedure.
6. Once the E-Treat system has soaked for 24 hours close the
supply valve, place bypass into the service position and open a
nearby cold water faucet to relieve pressure from the system.
7. Disconnect the outlet line and place a bucket under outlet
of system.
8. Open the supply valve to the 1/4 open position and allow water
to run into the bucket until water runs clear then turn off the
supply valve. If outlet is flowing into a bucket, water could
splash on nearby objects. If this threatens the safety, value,
structure, or appearance of these objects, protect/remove
them or use the outlet to drain option.
9. Connect the outlet of the E-Treat system to the cold water
supply to the house and slowly fully open the supply valve.
10. Open hot and cold faucets downstream from the E-Treat
system to relieve any air from the plumbing system and water
heaters. Then close the faucets.
11. Check for leaks. Repair as needed.
Содержание 68101336
Страница 12: ......