Watts Premier B-RO5M-50 Скачать руководство пользователя страница 7

Страница: 7 / 32

Page 7

AG-SS with TDS Monitor Faucet Installation

Step 6

Step 7

Remove the stem nut and the tubing guide from the faucet.

Make sure the soft rubber gasket remains, so it will be on top

of the counter when installed. From above the sink, feed the

tubing and faucet stem down through the 1¼ inch mounting

hole in the sink.

From below the sink, slide the tubing guide up the threaded

stem and follow it with the mounting nut, turning the nut

clockwise until fully tightened.

Insert the blue tubing (part# 610113), into the end of the

threaded stem. Make sure to push in ﬁrmly to ensure the

tubing is locked in place. (NOTE: this tubing will also be used

for the ﬁnal ﬁlter installation page 13)

Refer to

Black Tube Connection

and

Red Tube

Connection

steps on pages 12 & 13 of this manual to

complete the faucet installation.

Remove the spout from the top of the faucet by pulling it

straight upward. Remove the faucet knob by pinching the

two locking tabs inward and then pulling upward on the knob

while the tabs are pinched inward. Push the coin cell battery

into the battery holder behind the circuit board.

NOTE: the +

side of the battery goes against the gold metal bracket.

When the battery is iinstalled, the red and green indicator

lights will go through a ﬂashing sequence, followed by

only the green light ﬂashing. At this time, make your TDS

selection on the DIP Switch, only one switch is to be pushed

up. Refer to the chart below to determine which switch you

want to push up.

Note:

If using the AG-SS TDS Monitor Air Gap Faucet , a 1 1/4” hole will be
required.

Step 8

Step 9

Note:

Replace the knob by centering it over the faucet and aligning the trough on the

inside of the faucet knob with the valve lever. Lower the knob making sure the

valve lever slides into the trough, making sure the knob top hole is centered

over the locking tabs. Push the knob all the way down until it locks in place.

Push the spout back into the top of the faucet so that it is fully seated and

push the frosted deﬂector down until fully seated. You may have to rotate the

deﬂector until it is in position to be fully seated.

After completing the installation of your RO system, you should see the

green light ﬂash at the base of the faucet while water is ﬂowing through the

faucet

(the red light may ﬂash when system is ﬁrst turned on, this will

turn green following the initial tank ﬂush)

When the system is ready to be serviced (six to 12 months) you will see the

ﬂashing light switch from green to red, indicating it is time to replace your

ﬁlter cartridge(s).

Step 10

1 - 30 ppm

5 - 150 ppm

2 - 60 ppm

6 - 200 ppm

3 - 90 ppm

7 - 250 ppm

4 - 120 ppm

8 - 300 ppm

SWITCH SELECTION FOR TDS

Содержание B-RO5M-50

































Результаты поиска

Содержание B-RO5M-50

Отзывы:

Watts Premier B-RO5M-50, Инструкция по установке, эксплуатации и обслуживанию, Страница: 7 / 32

Результаты поиска

Содержание B-RO5M-50

Отзывы: