background image

CommLink IV Technical Guide            

18

   Operator Interface 

Troubleshooting the USB Drivers for Windows

®

 Vista

Troubleshooting Tips

Problems with Prism Software

  

Verify that the correct COM port, created by the USB 

• 
  connection, is selected in the 

Job Site Window

. Verify 

  COM port number in 

<Control Panel>

<System>

 

<Hardware>

<Device Managers>

<Ports>

.

If using Prism II, verify that CommLink 4 is selected 

• 
  for Type of CommLink in the 

Job Sites Window

.

If using Prism, verify that the Baud Rate is set to 19200 

• 
 in 

the 

Job Sites Window

.

Verify that the correct CommLink mode is selected 

• 
  under Network Confi guration in the

 Job Sites Window

.

Verify that the USB switch on the back of the

• 
  CommLink is set to Normal.

Problems with USB Connection

Verify that the RX-USB and TX-USB are blinking

• 
  when you perform a Search for Units or try to open a 
  status screen in Prism.

If the USB LEDs fail to blink, disconnect and

• 
  reconnect the USB connection. 

If the problem persists, verify that the USB drivers

• 
  have been installed properly. See next sections entitled, 
  “Troubleshooting the USB Drivers.”

Problems Viewing Controllers on a Network

Make sure that the CommLink communication dip 

• 
  switch is set to Multi.

Make sure that in Prism, the CommLink fi eld in the 

• 

Job 

 Sites 

Window

 is set to zero for multiple loop.

In Prism II, make sure that Multiple Loop

• 
 Confi guration is selected for Network Confi guration in   
 the

 Job Sites Window

.

 

NOTE: 

WattMaster Controls Technical Support cannot 
troubleshoot internal PC and/or Windows-based 
operating system problems.

NOTE:

 

WattMaster Controls Technical Support cannot 
troubleshoot fi rewalls, routers and/or problems on 
a customer’s internal or external network. An IT 
professional may need to be consulted.

Troubleshooting the USB Drivers for 
Windows

®

  Vista

If the 

Found New Hardware Window

 did not appear when 

you plugged in your CommLink or if you canceled out of the
installation procedure for any reason, you will have to follow 
these instructions to install the USB drivers.

1. 

Plug

 the USB cable attached to your CommLink into 

your computer’s USB port.

2. 

Insert

 the USB Drivers CD-ROM into your CD-ROM 

drive.

3.  

Click

 

<Start>

 and then 

click

 

<Control Panel>

Once in the Control Panel, 

select 

Classic View and 

then 

double-click

 the 

<Device Manager>

 icon.

4. The 

Device Manager Window 

will appear. In this 

window, look for an exclamation point in the
categories, “Other devices,” “Ports,” or “Universal 
Serial Bus controllers.” 

Click

 the item containing the 

exclamation point. 

 

Содержание CommLink IV

























Отзывы: