WattAge Mirage 2000-5 Скачать руководство пользователя страница 7

tem to run the motor. Looking at the motor, the
shaft should turn clockwise. If it does not turn
clockwise, reverse the motor polarity.

o

)

9. To reduce the chance of failure as well

as reducing the voltage loss from plugs, we rec-
ommend direct soldering the motor wires to the
speed control. However, if you need to use plugs,
Tamiya style plugs have been included in the
kit for your convenience.

o

)

10. Position the receiver and speed control

as shown. The speed control can be positioned
rearward if needed to prevent radio interfer-
ence. However, positioning the radio as shown
should help balance the aircraft without the need
for adding weight.

o

)

11. The plastic cover sets over the radio

compartment. Make small guide holes and then
install the cover with the 4 screws provided.

Receiver

Speed Control

A n t e n n a
Wire

Cover for radio compartment

Install with 4 wood screws

Recessed area for launching
grip area

o

)

1. The Vertical Stabilizer is mounted on top

of the fuselage. Notice the flat area at the end
of the fuselage.

o

)

2. To align the stabilizer, draw a centerline

6 7/8" on the fuselage top. Use the foam mold
marks as a guide.

o

)

3. Test fit the stabilizer. It should be per-

pendicular to the wing (90 degrees). Lightly
sand the stabilizer mounting-surface if it does
not align properly.

Vertical Stabilizer Installation

o

)

4. Once satisfied with the fit, use epoxy to

glue the stabilizer to the fuselage (The same way
described for the wing.)

Draw a centerline.

Use the mold
marks as a guide

90 degrees

o

)

1. In order for your Mirage to fly prop-

erly, the clear plastic reflex tabs must be in-
stalled.

o

)

2. Trim the tabs as shown. Be sure to leave

a small area (Approx 2mm) around the tab to
act as a gluing surface.

o

)

3. Test fit the tabs. The tall side should be

aligned with the wing’s trailing edge.

o

) 4. Install with epoxy just outside of the

elevons.

Reflex Tab Installation

Remove
Shaded Area

Cut
Here

Leave 2mm
edge around
the tabs

Match high
point of the
tab with the
wing’s trailing
edge.

Place tab here

7

Содержание Mirage 2000-5













Отзывы: