Watson Marlow Pumps 500 Series Скачать руководство пользователя страница 156

Страница: 156 / 157

List of tables and figures

33.1

Tables

Table 1 - Specification ratings

Table 2 - Weights

Table 3 - Conductor colour coding

Table 4 - Wiring the D-Connector

Table 5 - Input/output Connectors

Table 6 - External interface parameters

Table 7 - Allowance for one additional connection pair

Table 8 - First-time start-up defaults

Table 9 - PLC Errors

Table 10 - Configure PROFINET® settings

Table 11 - Pump details and set up

Table 12 - Pump Status

Table 13 - Pump Control

Table 14 - Errors and warnings

Table 15 - Dispense

Table 16 - Acyclic data records

Table 17 - GSDML compatibility guide

Table 18 - Maximum pump speed

108

Table 19 - Sensor units

122

Table 20 - Sensor pressure limits

124

Table 21 - Sensor flow limits

124

Table 22 - Error codes

133

Table 23 - Drive spares

136

Table 24 - General guide to cleaning with solvents

140

Table 25 - 1.6 mm wall tubing for 520R pumpheads

142

Table 26 - 2.4 mm wall tubing for 520R2 pumpheads

143

Table 27 - 2.4 mm wall elements for 520RE pumpheads

143

Table 28 - 2.4 mm wall elements for 520RE pumpheads

144

Table 29 - 2.4 mm wall elements for 520RE pumpheads

145

Table 30 - 4-7 bar (60-100 psi) pressure rated elements

145

Table 31 - 1.6 mm wall elements for 520RET pumpheads

145

Table 32 - 1.6 mm wall elements for 520RET pumpheads

145

Table 33 - 1.6 mm wall elements for 520RET pumpheads

145

Table 34 - Pumphead spares

146

156

m-530pn-en-09 02-02-22

Содержание 500 Series






























































































































































Результаты поиска

Содержание 500 Series

Отзывы:

Похожие инструкции для 500 Series

Бренды по названию

Популярные бренды

Watson Marlow Pumps 500 Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 500 Series

Отзывы:

Похожие инструкции для 500 Series

Бренды по названию

Популярные бренды