8
JET 1 (SPEED) ICON:
Tap the white JET 1 icon once to turn Therapy Pump 1 on. Jet 1 will run at 40% speed (default setting low), and the
yellow jet low icon will appear on the display. If left running, the current speed will be displayed for 15 seconds. Tap the number on the
screen to change the JET 1 speed, scroll to the desired speed and tap SAVE to save the setting, or EXIT to reverse without saving.
Wait for several seconds for JET 1 to reach the desired speed. Any time the display shows speed, tap the number, scroll to the desired speed,
and SAVE the new setting or EXIT to maintain the previous pump speed. When the display shows the water temperature tap the JET 1 icon,
and the speed will appear on the display.
When the spa is in HEAT MODE (heater is on), the speed cannot be set below 40%. When the spa is in FILTRATION MODE the speed can be
set between 0-99%. The orange jet high icon appears on the display when the pump speed is equal to or exceeds 50%. The yellow jet low
icon appears on the display when the pump speed is below 50%. To stop the pump, tap the JET 1 icon when the speed number is displayed.
If the spa is in a filter cycle, JET 1 pump speed will change to a preset filter cycle speed.
JET 2 (2-SPEED PUMP 2) ICON:
Tap the white JET 2 icon once to run JET 2 on low. Tap a second time for high, and a third time for off. The
Icon will change color to yellow for low speed and to orange for high speed. If left running, low speed turns off after 60 minutes and high
speed turns off after 15 minutes. Users can change these default times in “General Setting”/“Device Timeout” Setting Screen.
JET 1 (THERAPY) ICON:
Tap the white JET 1 THERAPY icon once to turn on JET 1 (VS) to one of 18 preprogrammed therapy cycles (therapy
number). The duration of each cycle is 15 minutes and will automatically turn off at the end of the cycle. Each therapy cycle is unique and
simulates a different type of massage therapy. To change the therapy number tap the yellow number under JET 1 THERAPY. Scroll to the
desired therapy number (1-18) and tap SAVE, or EXIT to maintain previous therapy setting. The heater will turn off while the spa is in
Therapy mode.
LIGHT ICON:
Tap the white LIGHT icon to turn the spa light on; the LIGHT icon will change color to yellow. Choose from: Red, Green, Blue,
Magenta, White, Slow Color Wheel, Fast Color Wheel, and Strobe. Tapping one of these options will turn the light to the selected mode. The
light will automatically turn off after 60 minutes. Users can change the default times in “General Setting”/“Device Timeout” setting Menu.
SEAT CONTROL PANEL OPERATION (AUXILIARY PANEL):
For spas equipped with therapy variable speed pump.
The pump is dedicated to one or two
hot tub seats and a seat equipped with the seat control panel. The panel has 4 buttons and a display: “Up”, “Down”, “Speed”, & “Therapy”. • To adjust
the pump speed press the “Speed” button; the display will show the current speed, then press the “Up” or “Down” button to set the desired speed. The
Display will show the new speed. Speeds range from 0-99%. • To switch to Therapy mode press the “Therapy” button. The display will show a “Therapy
Number” between 1 and 18. To change the “Therapy Number” press the “Up” or “Down” button to choose the desired “Therapy Number”. The pump
will start immediately and provide the selected therapy cycle. The duration of each cycle is 15 minutes.
SPA CIRCULATION AND FILTRATION:
Your system is equipped with a variable speed pump. JET 1 provides continuous water circulation, filtration and
sanitation. A dedicated, high performance variable speed pump running on low speed constantly draws water from the spa filter, runs it through the
heater (heating only when necessary), and moves water back to the spa. The ozone output is on when JET 1 is running in filter mode. The ozone will
turn off for one hour if a user taps any button on the top side panel (spa in use). See filter cycle setting (1-4) in TP500 setting screen.
NOTE: Using variable speed technology significantly increases spa efficiency, and setting pump speed to the lowest level can save money. Please be
careful when choosing pump speed in filtration cycles, if it is set too low it can interrupt water filtration (skimming). We do not recommend setting pump
speed to less than 30% in filtration cycles.
HEATER OPERATION:
Your spa is equipped with an electrical heater. By setting your thermostat to the desired temperature, your heater will
automatically turn on and off as needed. The temperature set point (Set Temperature) can be adjusted from 60°F to 104°F/15.5°C to 40°C. To change
the water Set Temperature tap the temperature number and scroll to your desired temperature. Tap the SELECT button to save the setting, or EXIT to
return to the Main screen. Changing the Set Temperature will make JET 1 turn on (if it was off) to get an accurate temperature reading and determine
if the water needs to be heated. The startup temperature is set at 100°F/37.5°C. The last measured temperature is constantly displayed on the screen.
The heater is off when JET 1 is running in “Therapy” mode.
SPA FUNCTION ICONS
THERAPY SPA WITH VARIABLE SPEED PUMPS
The TP500 operates and programs your spa. The basic function icons are described below.
