background image

 

 

Impeller Cleaning

 

1. Unplug the pump. 

2. Remove the three screws shown in the figure. 

3. Remove the cover and carefully clean the impeller of all debris. 

4. Before reattaching the cover, carefully reposition the gasket making sure it will not

 

 

 

 

 

 

 

 

 

   

 

 

obstruct the pump openings. 

5. Reinstall the cover and replace the screws using caution as to not over-tighten or

 

 

 

 

 

 

 

 

     

 

   

strip the screws.  

 

 

 
 

 

 

 

 

Key Pumping Considerations

  

1. A 12V DC battery source power source is required for the HydraPump® 12V Utility

 

 

 

 

 

 

   

 

 

 

 

 

 

Submersible to operate. It must be an adequately charged battery, preferably a fully

   

   

     

 

 

 

   

 

charged battery since it will offer the best experience. 

 

2. The pump should be in the off position when making the battery connections. 

3. Check that the water source and piping are clear of dirt, scale, and sand. Debris will

 

 

 

 

 

 

 

 

   

 

 

 

 

 

 

clog the pump. The pump is meant for clean/clear water. 

4. The pump and its piping cannot operate below freezing. 

5. The pump motor is in a fully enclosed oil filled compartment which helps with keeps

 

 

       

 

   

 

 

 

 

 

 

the pump cool during operation. Also, the pump should not operate without water

 

 

 

 

 

 

 

 

 

 

 

 

 

present for extended periods but if it does: unplug the pump and check the pump for

   

 

 

     

 

 

 

 

 

 

 

   

damage. 

 

 

 

06

03 

Cleaning & Maintenance 

 

 

Always disconnect the power source before attempting to

 

 

 

 

 

 

   

clean the impeller. 

Содержание HYDRAPUMP












Отзывы: