manualshive.com logo in svg

Waterous PB18 Series, Руководство по эксплуатации

Поделиться
Скачать
Waterous PB18 Series Скачать руководство пользователя страница 16

IL1323

Drive Gear

Square Key, 1/4 x 1 in.

Washer

Hex Hd Screw, 3/8-24 x 1-1/8 in.

8.

Remove the hex head screw and washers that
hold the drive gear to the engine crankshaft.

9.

Pull the drive gear off the shaft.

10. Remove the key.

OVERHAUL - GEARED PUMP

Page 15 of 20

CAUTION

Do not damage the internal
thread of the shaft.

Figure 12. Drive Gear Removal

Flat Copper Washer, 3/8 in.

Socket Head Screw, 3/8-16 x 1-1/4 in.

IL1324

Gear Case Subassembly

Shaft Sleeve

O-ring

Oil Seal

11. Remove the (4) socket head cap

screws and washers holding the
gear case to the engine.

12. Remove the gear case.  Press out

the shaft seal.

13. If oil has been leaking past the shaft

sleeve, the O-ring and oil seal
should be replaced.  Remove the
sleeve.  Do not mar the sleeve sur‐
face under the seal.

14. Clean the magnetic drain plug and

check to be sure the breather is not
plugged.

Figure 13. Gear Case Removal

Содержание PB18 Series























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды