Waterous E500 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 22

background image

PUMP OVERHAUL

Page 9 of 21

E511-C Impeller and Mechanical Seal Removal

Square Key, 3/16 x 1 in., SS

Mechanical Seal

Wear Ring

Impeller

Nord-Lock

→

Washer, 3/4 in., SS

Impeller Nut

1.

Remove  the  impeller  nut  and  washer  from  the  impeller
shaft.  If the impeller  does not pull  off the  impeller  shaft
easily,  use  a  gear  puller  or  two  pry  bars  between  the
impeller and adapter.  Remove the impeller key.

2.

Use snap ring pliers to remove the retaining ring. The
mechanical seal can then be removed. Note: Do not
reuse the retaining ring. The stationary ring will remain
with the gear case cover.

3.

Drain oil from gear case.

Magnetic Pipe Plug, 3/8 in.

Retaining Ring

E501-C Gear Case Cover and Impeller Shaft Removal

1.

Remove the impeller gasket.

2.

Remove the 10 hex head screws and lock
washers from the gear case cover.

3.

Remove the gear case cover from the gear
case. Press out the impeller shaft and bear-
ing assembly from the gear case cover.

4.

Remove gear case gasket.

5.

Press out the mechanical seal stationary seal
ring, oil seal. Pull wear ring if required.

O-ring

Oil Seal

Stationary Ring

Impeller Gasket

Impeller Shaft and Bearing Assembly

Gear Case Gasket

Wear Ring

Hex Hd Screw, 3/8-16 x 1 in.

Gear Case Cover

Lock Washer, 3/8 in.

«
...
8
9
10
11
12
...
»

Содержание E500 Series























Отзывы:

Нет отзывов

Похожие инструкции для E500 Series

Бренд: Wacker Neuson Страницы: 38

Бренд: Tebas Страницы: 14

Бренд: Little Giant Страницы: 8

Бренд: ProMinent Страницы: 77

Бренд: Dometic Страницы: 10

Mini-CHIEMSEE B 1100

Бренд: SHG Страницы: 26

Бренд: Nagman Страницы: 15

Tranquility TR Series

Бренд: ClimateMaster Страницы: 96

Бренд: Trane Страницы: 8

Бренд: Virax Страницы: 52

Бренд: Asada Страницы: 28

Бренд: IPM Страницы: 24

Бренд: A.O. Smith Страницы: 24

Бренд: Clarke Страницы: 12

Бренд: Zodiac Страницы: 10

Бренд: YAMADA Страницы: 30

Бренд: STIEBEL ELTRON Страницы: 56

Altherma CHYHBH-AV32

Бренд: Daikin Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды