WaterFurnace Geothermal heating and cooling system, Руководство пользователя

Страница: 29 / 66

27
Choose the System Setting (Heat, Off, Cool, Auto)
Press the SYSTEM button to select:
Heat
: Thermostat controls only the heating system.
Off
: Heating and Cooling systems are
off.
Cool
: Thermostat controls only the cooling system.
Auto
: Auto Changeover is used in areas where both heating and cool-
ing may be required on the same day.
AUTO
allows the thermostat to automatically select heating or cooling depending on the
indoor temperature and the selected heat and cool temperatures. When using
AUTO
, be sure to set the Cooling temperatures
more than 1° Fahrenheit higher than the heating temperature.
Manual Operation for Non-Programmable Thermostats
Press the SYSTEM button to select Heat or Cool and use the or buttons to adjust the temperature to your desired setting.
After selecting your desired settings you can also press the SYSTEM button to select
AUTO
to allow the thermostat to automatically
change between Heat and Cool.
Manual Operation (Bypassing the Program) Programmable Thermostats
Press or and the HOLD button and adjust the temperature wherever you like. This will override the program. The
HOLD
feature bypasses the program and allows you to adjust the temperature manually, as needed. Whatever temperature you set in
HOLD
will be maintained 24 hours a day, until you manually change the temperature or press
Run Schedule
to cancel
HOLD
and resume the programmed schedule.
Program Override (Temporary Override)
Press or buttons to adjust the temperature. This will override the temperature setting for a (default) four hour override
period. The override period can be shortened by pressing or lengthened by pressing . Program Override period can
range from 15 minutes to 7 days.
Example
: If you turn up the heat during the morning program, it will be automatically lowered
later, when the temporary hold period ends. To cancel the temporary setting at any time and return to the program, press
Run
Schedule
. If the SYSTEM button is pressed to select
AUTO
the thermostat will change to Heat or Cool, whichever ran last. If
it switches to heat but you want cool, or it changes to cool but you want heat, press both or buttons simultaneously to
change to the other mode.
PROGRAMMING
Set Current Time and Day
1) Press Menu and then Set Time button once. The display will show the hour only.
2) Press and hold either the or key until you reach the correct hour and AM/PM designation (AM begins at midnight,
PM begins at noon).
3) Press Set Time once again. The display window will show the minutes only.
4) Press and hold either the or key until you reach the correct minutes.
5) Press Set Time once again. The display will show the day of the week.
6) Press the or key until you reach the current day of the week.
7) Press Run Schedule once. The display will show the correct time and room temperature alternately.
Enter the Heating Program
1) Press the Menu button and then press Set Schedule. Press SYSTEM button to select either “Heat” or “Cool” in the system
switch area indicating the active mode being programmed. You can switch to the other mode by pressing the system switch at
any time.
2) The top of the display will show the day(s) being programmed. The time and set at temperature are also displayed. “Morning”
will also be displayed to indicate the period.
3) Press or key to change the temperature to your selected temperature for the 1st heating period (Morning).
4) Press or key to adjust the start time for period.
5) The time will change in 15 minute increments.
6) After you have set the time and the temperature for the period to begin, press Set Schedule to advance to the next program period.
7) Repeat steps 2 through 6 until all of the program times and temperatures are set for all program periods on that day.
8) Press “Advance Day” to change to the next day and repeat steps 2 through 8.
9) When programming is complete and all of the times and temperatures match your desired heating schedule, press Run
Schedule. The thermostat will now run your program.
Enter the Cooling Program
1) Press the SYSTEM button until the Cool icon appears.
2) Follow Enter Heating Program instructions for entering cooling times and temperatures.
For more information on thermostat operation, refer to the instruction manual shipped with your thermostat.
THERMOSTAT OPERATION
TP32W02 Thermostat - Continued