Waterco 20 SC Скачать руководство пользователя страница 9

I pg 07

Waterco Hydrochlor®

Note:

 When the LED lights flash it is an indication of:

•  Low salt level
•  Low temperature or 
•  Cell plates wearing

If you don’t know what your salt level is or how to test it, consult your local pool care specialist.

Water Chemistry

It is important to maintain the correct water chemical balance in the swimming pool; this will help 
protect the Electrochlor chlorinator unit and its cell.

Consult the local pool professional for the correct water balance according to the swimming pool 
type.

The Electrochlor chlorinator will run correctly at the following chemistry levels

Range

Suggested

pH.                                     

7.2 – 7.8                      

7.2 – 7.6

Total alkalinity                     

60 – 200ppm                 

80 – 150ppm

Calcium hardness                

100 – 500ppm               

60 – 250ppm

Stabilizer (Sun screen)        

30 – 60ppm

SALT CELL CLEANING PROCEDURE 

a.  Press the MODE key until OFF on the power pack, then turn the pump and 

Hydrochlor to standby mode.

b.  Unscrew the barrel unions from the salt cell and disconnect the cables 

from the salt cell’s brass connectors.

c.  Turn the salt cell housing upside down with both ports facing upwards.

d.  Pour the Cell Wash cleaning solution into the housing to dissolve the calcium build-up from the 

salt cell plates. There should be just enough solution to cover the salt cell plates. 

e.  Allow enough time for the solution to dissolve the calcium build-up from the salt cell plates. 

Approximately 5 to 10 minutes.

f.  Once the calcium build-up has been removed, pour out the Cell Wash solution into a bucket and 

lightly rinse-off excess calcium and Cell Wash solution from the salt cell assembly, with fresh 
water.

g.  Reconnect the salt cell onto the filter system

h.  Press the 

MODE

 button to AUTO  or ON  on the power pack to reactivate the Hydrochlor.

 

Never use products that are not specifically manufactured to clean the Hydrochlor®’s salt 
cell. Do not use raw acids such as Hydrochloric acid. This will damage the salt cell and 
severely shortens its life and will void warranty. Please consult your local pool professional 
for advice on salt cell cleaning products.

Содержание 20 SC













Отзывы: