Waterax Versax Скачать руководство пользователя страница 17

Страница: 17 / 30

WATERAX

VERSAX Owner's Manual

11/2015

Service

This section includes instructions for overhaul and maintenance requiring disassembly of
the

WATERAX

VERSAX series pumps. It

does not

include engine maintenance. For

maintenance instructions regarding the engine, as well as for oil and fuel
recommendations, please refer to the engine manufacturer’s manual.
Note: It is recommended that all fasteners be replaced with genuine

WATERAX

parts.

Parts Breakdown

Figure 1: Exploded view of the VERSAX 6HP pump end (portable configuration).

ID ITEM NO DESCRIPTION

QTY ID ITEM NO DESCRIPTION

QTY

1 800208

VSC124 NUT CASING VERSAX

19 701162*

SUPPORT BRACKET PUMP END VERSAX

2 800216

VSC130 YOKE 3/4" SHAFT VERSAX

20 800227

VSC122 O-RING FOR DRAIN PLUG VERSAX

3 800221

VSC121 O-RING CASING VERSAX

21 800195

VSC117 PLUG 1/4" DRAIN VERSAX

4 800228

VSC123 SEAL FOR BOLT VERSAX

22 800191

VSC116 GASKET - CLACKER ASSY VERSAX

5 800217

VSC133 BOLT 5/16" X 1-1/4" VERSAX

23 800199

VSC115 FLANGE - SUCTION 2"NPT VERSAX

6 800213

VSC129 SEAL - MECHANICAL 3/4"

24 800211

VSC126 SCREW M8 VERSAX

7 800215

VSC128 STUB SHAFT 5/8" VERSAX

25 800192

VSC118 CASING VERSAX

8 800226

VSC132 IMPELLER SHAFT 5/8" VERSAX

26 800201

VSC125 BOLT - CASING VERSAX

9 800229

VSC131 WEAR RING 3/4" SHAFT VERSAX

27 800224

VSC107 GASKET - DISCHARGE VERSAX

10 800194

VSC114 DIFFUSER - 2ND STAGE VERSAX

28 300512*

ADP-A-C15S-NC 1.5 NPSH CAP W/O CHAIN

11 800198

VSC113 O-RING DIFFUSER - INTERS VERSAX

29 800230

VSC108 FLANGE - DISCHARGE VERSAX

12 800214

VSC127 SPACER SLEEVE 5/8&3/4SHA VERSAX

30 300762*

ADP-A-C10S-NC 1 NPSH CAP W/O CHAIN

13 800190

VSC112 DIFFUSER - INTERSTAGE VERSAX

31 300761

ADP-A-C20BSP-NC 2 BSPP CAP W/O CHAIN

14 800189

VSC111 WASHER M10X30 VERSAX

32 800209*

VSC105 NUT-BUSH 3/8" FOR HANDLE VERSAX 2

15 800220

VSC120 WASHER (SPRING)-IMPELLER VERSAX

33 800223*

VSC103 HANDLE VERSAX

16 800207

VSC110 SCREW - IMPELLER VERSAX

34 800202*

VSC104 BOLT-CASING FOR HANDLE VERSAX

17 800222

VSC109 SUCTION COVER VERSAX

* Not included on vehicle mount configuration.

18 800187

VSC119 O-RING SUCTION COVER VERSAX

Содержание Versax































Результаты поиска

Содержание Versax

Отзывы:

Похожие инструкции для Versax

Бренды по названию

Популярные бренды

Waterax Versax, Руководство пользователя

Результаты поиска

Содержание Versax

Отзывы:

Похожие инструкции для Versax

Бренды по названию

Популярные бренды