background image

18

19

13 .  Prior to reinstalling the discs, the drive shaft should be removed and the O-rings cleaned, inspected and lubricated with 

Dow #7 silicone grease . The shaft can now be installed into the disc prior to installation . 

14 .  With the outlet disc assembled to the shaft, the orientation of the shaft to inlet disc can be assured by installing the set 

with the through hole on the outlet disc at the 6 o’clock position . The easiest way to reassemble is to remove both disc 

drives and assemble the outlet side first . Then each disc can be fitted on the shaft individually . At this point the transfer 

valve cap assemblies can be reinstalled .

NOTE:

 Both transfer caps only mount in one orientation . Prior to installation of cap assembly, be sure to check that the 

stainless steel spring and the plastic spring support is in place and attached to the inside of the assembly . 

15 .  Wipe the outside edge of the O-ring on the cap and the inside 

mating area of the valve with a clean cloth and reapply a thin 

layer of Dow #7 silicone grease . 

16 .  Noting the one possible orientation of the transfer drive cap, 

use one hand to press in and support the transfer drive cap 

while using the opposing hand to start two screws in, one 

on the top and one opposing it on the bottom . Tighten the 

screws evenly so that the cap seats the O-ring without 

getting pinched or damaged . Screws should only be hand 

tightened with a 5/32” or 4 mm Allen wrench . 

DO 

NOT OVER TIGHTEN SCREWS.

NOTE:

 Take care to be certain the meter cable 

doesn’t get under the drive cap while tightening 

as it will result in damaging the cable . 

17 .  Position the large white drive gear with the “A” 

pointing toward the one o’clock position and then 

press it onto the stainless steel drive shaft, making 

sure it snaps and locks into position . 

NOTE:

 The white drive gear is splined to the drive 

shaft and will only assemble in one orientation . 

Because of this, it is not necessary that the discs and 

gear be exactly positioned . The positioning needs to be 

approximate but they have to fit on the shaft .

18 .  Install the larger black reducing gear onto the stainless steel 

shaft, then install the remaining smaller reducing gears from 

left to right . 

19 .  Reinstall the grey reducing gear cover over the gears and affix 

with the three stainless steel screws . 

20 .  Reinstall the drive motor by pressing the spring clip loop to the right, then rotate the motor as you are inserting it so the 

gear of the motor meshes properly with the reducing gears . 

21 .  Release the spring clip loop and rotate the motor until the motor housing engages with the plastic nub inside the housing 

that holds the motor in place, making sure that the top of the motor is flush with the top of the grey gear housing . 

22 . Press the drive motor wires down into the strain relief of the drive cap .

23 . Reinstall the cover assembly .

After completing any valve maintenance involving the valve drive assembly or the transfer drive assembly, press and hold 

the 

NEXT

 and 

REGEN

 buttons simultaneously for three to five seconds to perform a soft reset which will synchronize the control 

valves positions .

SERVICE INSTRUCTIONS

FIGURE 3

Содержание Impression Plus Series





































Отзывы: