background image

11

5.

ERROR MESSAGE:

If the word “ERROR” and a number are

alternately flashing on the display record the number and contact
the dealer for help. This indicates that the control valve was not
able to function properly.

6.  

BRINE TANK MAINTENANCE AND SALT:

Refill the brine tank as necessary, making sure at

least 1/3 of the brine tank is full at all times. Without proper salt levels, the water softener may
not operate properly.

Because “typical” settings of this water softener include a dry salt storage feature (no water in
brine tank between regeneration), the manufacturer recommends the use of solar salt for best
results. The brine tank is manufactured for the use of solar, pellets or rock salt. If pellet or rock
salt is used, a cleaning of the brine tank every six months is recommended. If the dry salt
storage feature is not being utilized, block salt may be used.

CAUTION:

The manufacturer does not recommend the use of any
resin cleaners, nor placement of any resin cleaners into
the brine tank. This may be harmful to the water
softener and for human consumption. Consult dealer
for proper cleaning instructions.

ERROR

Содержание IMP-844

































Отзывы: