Water Right IMP-1044, Инструкция по установке и руководство пользователя

Страница: 25 / 28

24 25
SPECIFICATIONS
Manufactured by Water-Right, Inc. • 1900 Prospect Court • Appleton, WI 54914 • 800-777-1426 • water-right.com SPE-IMP CERT RevA0720
* All Impression Plus water softeners are set at “minimum salting” from the factory.
1
Cabinet dimensions represent the High-Profile cabinet option. Low-Profile cabinets
are about one inch shorter in height than the High-Profile cabinet lid.
Impression Plus Series
®
Specifications
CABINET MODEL (IMPC) SPECIFICATIONS
MODEL
IMP-844 IMP-948 IMP-1044 IMP-1054 IMP-1248 IMP-1354
Rated Softener
Capacity:*
(Grains/Lbs. Salt)
Minimum 13,700 @ 3.4 18,200 @ 4.5 18,200 @ 4.5 27,600 @ 7.0 36,400 @ 9.0 45,800 @ 11.5
Medium 16,800 @ 6.0 23,500 @ 9.0 23,500 @ 9.0 36,700 @ 15.0 47,000 @ 18.0 53,900 @ 18.0
Maximum 18,800 @ 8.0 28,000 @ 15.0 28,000 @ 15.0 42,000 @ 22.5 56,100 @ 30.0 69,800 @ 37.0
Amount of High Capacity Cat-ion Resin Media (Cu. Ft.) .75 1.0 1.0 1.5 2.0 2.5
Efficiency at 1 lb Salt Setting (Grains/Lbs Salt) 4,040/1 4,040/1 4,040/1 4,040/1 4,040/1 4,040/1
Max. Service Flow Rate (GPM) 11.7 13.1 16.0 13.3 16.4 17.1
Max. Pressure Loss at Max. Service (PSI) 15 15 15 15 15 15
Min. to Max. Working Pressure (PSI) 30-100 30-100 30-100 30-100 30-100 30-100
Min. to Max. Operating Temperature (ºF) 33-100 33-100 33-100 33-100 33-100 33-100
Max. Flow to Drain During Regeneration (GPM) 1.3 1.7 2.2 2.2 3.2 3.2
Electrical Requirements (volts-hertz) 110-50/60 110-50/60 110-50/60 110-50/60 110-50/60 110-50/60
Pipe Size 1” 1” 1” 1” 1” 1”
Total Dimensions:
Media Tank and Valve 8”W x 52”H 9”W x 56”H 10”W x 52”H 10”W x 62”H 12”W x 56”H 13”W x 62”H
Brine Tank 18”W x 33”H 18”W x 33”H 18”W x 33”H 18”W x 33”H 18”W x 40”H 18”W x 40”H
MODEL
IMPC-835 IMPC-1035
Rated Softener
Capacity:*
(Grains/Lbs. Salt)
Minimum 5,100 @ 2.3 18,200 @ 4.5
Medium 7.300 @ 6.0 23,500 @ 9.0
Maximum 7,800 @ 7.5 28,000 @ 15.0
Amount of High Capacity Cat-ion Resin Media (Cu. Ft.) .50 1.0
Efficiency at 1 lb Salt Setting (Grains/Lbs Salt) N/A 4,040/1
Max. Service Flow Rate (GPM) 9.6 16.0
Max. Pressure Loss at Max. Service (PSI) 9.0 15.0
Min. to Max. Working Pressure (PSI) 30-100 30-100
Min. to Max. Operating Temperature (ºF) 33-100 33-100
Max. Flow to Drain During Regeneration (GPM) 1.3 2.2
Electrical Requirements (volts-hertz) 110-50/60 110-50/60
Pipe Size 1” 1”
Total Dimensions:
1
Cabinet
14” x 44.5”H x
20.5”D
14” x 44.5”H x
20.5”D
IMP SPECIFICATIONS
Width
Width
Height
Height
Depth
Low Profi le Cabinet
High Profi le Cabinet
CYCLE TIMES (in minutes)
MODEL IMP-835 IMP-948 IMP-1044 IMP-1054 IMP-1248 IMP-1354 IMPC-835 IMPC-1035
Brine Refill 2 3 3 4.5 6 7.5 1.5 3
Regenerant (lbs) 3.4 4.5 4.5 7.0 9.0 11.5 2.3 4.5
Service 240 240 240 240 240 240 240 240
The above sequence takes place prior to regeneration; therefore, minutes are not included in totals.
Backwash 6 8 8 8 10 10 6 8
Brine and Rinse 40 60 60 90 90 90 40 60
Rinse 4 4 4 4 4 4 4 4
Total 50 72 72 102 104 104 50 72
Manufacturer recommends the use of coarse solar salt in these water softeners.
IMP -844, -948, -1044, -1054, -1248, -1354 and IMPC -835 -1035 softeners are certified by WQA against NSF/ANSI Standard 44 for the reduction of hardness as verified
and substantiated by test data.
Only the efficiency-rated water softener models have a rated capacity of not less than 3,350 grains of total hardness exchange per pound of salt (based on NaCl) and
shall not deliver more salt or be operated at a sustained maximum service flow rate greater than its listed rating. Efficiency is measured by a laboratory test described
in NSF/ANSI 44. The test represents the maximum possible efficiency the system can achieve after the system has been installed. The operational efficiency is typically
less than the efficiency due to individual application factors including water hardness, water usage, and other contaminants that reduce the softener’s capacity.
These water softeners are not intended to be used for treating water that is microbiologically unsafe or of unknown quality without adequate disinfection before or
after the system.